Cannes 2 ton c
Cannes IndustrThe purpose of hydraulic lifting platform Users can choose the power mode and configuration according to their own scope of use: power systems include: DC power supply, single-phase or three-phase power supply, diesel engine.
Frequently check for water accumulation and humidity. It is inevitable for aerial vehicles to drive in rainy and snowy weather, or muddy roads. The bottom and some gaps and indoor floors are prone to sludge accumulation. If the owner does not clean them in a timely manner, this can cause moisture to hide. Therefore, key holes bottom corners of tree trunks, and wiper brackets, as well as other areas, should be regularly inspected, and the drainage holes in the doors and various parts should be kept unblocked to ensure that the car seat covers, such as humidity carpets, and floors, prevent rust from forming parts.
Cannes .What is the solution to the problem of rust on the surface of the spiral elevator? Sandpaper has a large loss on the spiral elevator itself. Specializing in products,Cannes Outdoor cargo elevator, renewable resources business, including: elevator factory
Large logistics warehousing equipment service company with guaranteed prices and guaranteed services directly operated by the manufacturer. Because fixed elevators are mechanical equipment, the quality and performance of the product are good. Do not accept products from some manufacturers that do not meet the quality standards, in order to avoid some safety hazards in use.
.Hydraulic pump station: domestic lifting platform dedicated pump station, Italian imported pump station with external protective devices: organ m type, mesh type, and iron plate sealed type.
Test the goods elevator every day to see if it can operate normally.
It is strictly prohibited for personnel to climb up and down the floors by using the goods elevator privately.
The water cooling of hydraulic stations is generally tubular water cooling, and the type selection is based on the heat load to calculate the heat exchange area, while the air-cooled elevator is conducted using an air cooler, and the heat exchange capacity is calculated based on the heat load. Then, the type selection calculation is performed when the flow can be satisfied. Therefore,Cannes Chain guide rail type cargo elevator, the two types of cooling are different, and there are significant differences. Long-term lifting and lowering of cargo elevator factory
Transportation lifting platforms need to be considered. However, in the use of elevators, some relatively large locations will purchase lifting platforms suitable for their own needs based on user requirements which means that oversized equipment will have difficulties in transportation. This is also a concern for many users and manufacturers. The equipment is large in size and occupies a large area, making it difficult to move back and forth, and it is very difficult to move, So how should we solve it? Today, I will introduce to you in detail how large lifting platforms solve the problem of transportation difficulties.
Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, remove the motor shaft key.
Quality assurance.The motor winding is short-circuited. When a short circuit fault occurs in the motor winding, the short circuit current is much larger than the normal working current, which increases the copper loss of the winding, causing the winding to overheat or even burn out.
The motor winding is short-circuited. When a short circuit fault occurs in the motor winding, the short circuit current is much larger than the normal working current, which increases the copper loss of the winding, causing the winding to overheat or even burn out.
Connect the motor to the elevator naturally. During connection, it must be ensured that the concentricity of the elevator output shaft and the motor input shaft is consistent, and that the outer flanges of the two are parallel. Inconsistent centering can cause the motor shaft to break or the elevator gear to wear.
Hydraulic pump station: domestic lifting platform dedicated pump station, Italian imported pump station with external protective devices: organ m type, mesh type, and iron plate sealed type.
Total quality assurance.It is strictly prohibited for personnel to climb up and down the floors by using the goods elevator privately.
'The sinking of a cargo elevator is a phenomenon where the table surface drops due to gravity after a certain period of time after rising to a specified position. Of course, this problem must be abnormal,Cannes Guide rail type lifting cargo elevator, so how can we solve it?'? The first step is to find the reason, and the following editor summarizes the ultimate solution.
Motor connection error. When the triangular connection motor is mistakenly connected into a star shape, the motor still operates with full load, and the current flowing through the stator winding exceeds the rated current, leading to the motor stopping itself. If the stopping time is slightly longer and the power supply is not cut off, the winding will not only be severely overheated, but also burned. When a star connected motor is mistakenly connected into a triangle, or when several coil groups are connected in series into a single branch, the motor is mistakenly connected into two branches in parallel, both the windings and the iron core will overheat, and in severe cases, the windings will be burned.
Cannes .Does the cleanliness of the hydraulic station have relevant rules and requirements?
Connect the motor to the elevator naturally. During connection, it must be ensured that the concentricity of the elevator output shaft and the motor input shaft is consistent, and that the outer flanges of the two are parallel. Inconsistent centering can cause the motor shaft to break or the elevator gear to wear.
Carefully prepare a special construction plan for installation and construction