EstegormHigh performance elevatorOutstanding contribution in the lifting industry

Is the water cooling and air cooling of the hydraulic station the same?

Frequently check for water accumulation and humidity. It is inevitable for aerial vehicles to drive in rainy and snowy weather, or muddy roads. The bottom and some gaps and indoor floors are prone to sludge accumulation. If the owner does not clean them in a timely manner, this can cause moisture to hide. Therefore, activities in the outer edges of wheel hubs doors, bottom corners of tree trunks, key holes, and wiper brackets, as well as other areas, should be regularly inspected, and the drainage holes in the doors and various parts should be kept unblocked to ensure that the car seat covers,EstegormGuide rail lifting cargo elevator, such as humidity, carpets, prevent rust from forming parts.

Estegorm.The guide mechanism of the guide mechanism of the guide rail elevator manufacturer is mainly composed of guide plastic pipes, guide brackets compression springs, safety plugs, guide housings, and guide shafts. As a semi sectional view of the guide mechanism, a narrow gap is formed between the two guide plastic pipes, and the lifting cloth belt extends out of the box from this narrow gap to prevent the cloth belt from being tangled and serve as a guide. The safety plug is supported by a guide bracket and a compression spring. In order to prevent the compression spring from losing stability after being stressed, a small guide rod is designed on the safety plug, and the gap between the small guide rod and the spring is designed according to the table. The crane arm shaft is welded and installed with a crane arm hook at both ends. The material is selected and subjected to conditioning treatment. It forms three suspension points with the hook at the lower shell of the box. The soft support sling will be lifted by the person being lifted. The load bearing capacity of the crane arm is designed to ensure that the person being lifted can be in a comfortable state when riding. The distance between the two crane arm hooks is listed in the table as a design reference, and the balance bar is used to maintain the balance of the lifting device, The material is designed as a hollow tube, reducing the overall weight of the boom.

Large logistics warehousing equipment service company with guaranteed prices and guaranteed services, directly operated by the manufacturer. Because fixed elevators are mechanical equipment, in order to avoid some safety hazards in use.

.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be taken lightly. Moreover, from a professional perspective, there are relevant rules and requirements. You should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

Motor connection error. When the triangular connection motor is mistakenly connected into a star shape, and the current flowing through the stator winding exceeds the rated current, leading to the motor stopping itself. If the stopping time is slightly longer and the power supply is not cut off, the winding will not only be severely overheated, but also burned. When a star connected motor is mistakenly connected into a triangle, or when several coil groups are connected in series into a single branch, the motor is mistakenly connected into two branches in parallel, both the windings and the iron core will overheat, and in severe cases, the windings will be burned.

Several types: motor winding open circuit. When one phase of the motor winding is open circuit, it will cause three-phase current imbalance and cause the motor to overheat.

The motor winding is short-circuited. When a short circuit fault occurs in the motor winding,EstegormTwo ton guide rail type cargo elevator, the short circuit current is much larger than the normal working current, which increases the copper loss of the winding, causing the winding to overheat or even burn out.

Make sure to add butter twice a month to the transmission assembly where the grease fitting is located. For parts where butter cannot be added it is necessary to dredge the oil circuit or replace the grease fitting until butter can be added, hydraulic outriggers otherwise it is prohibited to use the equipment.

Knowledge popularization and superior performance of scissor fork type fixed lifting platform: equipped with safety devices to prevent overloading of the lifting platform; Equipped with a protection valve to prevent hydraulic oil pipe from cracking; Equipped with an emergency lowering device for sudden power failure; The doors of the upper and lower floors are equipped with safety devices that interlock with the system.

Fair price.Outriggers: mechanical outriggers, ordinary hand cranking outriggers, and pull-out outriggers.

Characteristics of hydraulic elevators: Hydraulic lifting platform products are divided into curved arm type hydraulic lifting machines, scissors type hydraulic lifting machines mast type hydraulic lifts,EstegormFixed guide rail lifting cargo elevator, and straight arm type hydraulic lifts according to their working modes. Hydraulic elevator is a replacement product of folding arm elevator (lifting platform) and scissor fork elevator (lifting platform). It can be widely used for the decoration and decoration of stations, docks, airports, hotels, posts and telecommunications, municipal gardens, garages, cleaning companies, public building facades, or the installation and maintenance of power systems, etc. This elevator has the advantages of light weight, self-propelled walking, electric starting, self supporting legs, simple operation, large working area, there will be some backflow, so it can be replaced at this time.

Before installing the elevator, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of each part connecting the motor and the elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.

Estegorm.To ensure excellent power supply at the installation site, install a separate distribution box. When using the distribution box, the electrical leakage switch must meet the requirements for construction elevators. If the installed construction elevator is variable frequency, the selection of the leakage switch should be compatible with the frequency converter.

Hydraulic pump station: domestic lifting platform dedicated pump station, Italian imported pump station with external protective devices: organ m type, mesh type, and iron plate sealed type.

Corrosion prevention measures for the body of aerial work vehicles Attention to small scratches The paint surface of aerial work vehicles often corrodes. In addition to common collisions, scratches, and small rocks on the drive tire, there can also be a paint peeling point that can cause a small rust over time. Because most of these scars are small and easy to ignore. Therefore, regularly inspect the engine compartment lid and surrounding areas, and once found, go to a professional beauty shop for processing in a timely manner.