Cage wooden box304 stainless steel plateWhat common sense needs to be understood

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, more kinetic energy should be digested and absorbed when the structure is destroyed which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle it has more advantages in strength. Medical copper tubes have many different s in practical application, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, rotating shafts, bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, communication, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes, the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus butter, oil, copper and aluminum pipes - and the old ones, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the sling should be relaxed, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

Some problems. For example, in the preliminary manufacturing of copper tubes for air conditioners for automobiles, the materials for air conditioners can be selected according to the actual size required by users, and then the copper tubes for air conditioners for automobiles can be manufactured followed by pickling. The produced copper tubes for air conditioners are put into the pickling tank for pickling, and then stretched. Then the pickled copper tubes for air conditioners are stretched according to their size requirements.

Cage wooden box.It has good electrical conductivity, corrosion resistance and processing properties, and can be welded and brazed.

Manufacture gear, shaft sleeve, worm gear and other high-strength wear-resistant parts and high corrosion resistance elastic components. Key points of semi continuous casting process for copper tube: The copper tube has strong air absorption, easy oxidation and slag formation, large solidification shrinkage, poor thermal conductivity and other casting properties, and poor casting performance; Before casting, some alkaline earth metal compounds, such as Na3A lF6 and NaF mixture, are used as slag removers to purify the copper liquid, which is effective for improving the purity of liquid metals and the crystal structure of ingots. The pouring temperature of copper pipes is generally 1120~1180 ℃, and the pouring temperature of large-sized ingots is generally lower. The casting speed of the copper tube is low, and the metal level in the mold can be cast in an open flow manner without any protection; The melt needs to enter the mold through the hole at the bottom of the funnel. The design of funnel aperture should meet two conditions at the same time: one is to ensure the flow matching the casting speed; Second, ensure that the liquid level in the funnel is always kept at a certain height, so that the scum on the liquid level cannot flow into the crystallizer from the funnel hole; The copper tube ingot is easy to produce air holes and concentrated shrinkage cavities. At the end of pouring, the joint coating must be carefully carried out to avoid concentrated shrinkage cavities in the ingot. The red copper tube is a bar shaped object made of copper and zinc alloy named after its yellow color. Copper content is 56%~68% brass, and its melting point is 934967 degrees. Brass has good mechanical properties and wear resistance, and can be used to manufacture precision instruments, ship parts, gun casings, etc. Different zinc content also has different colors. For example, when the zinc content is 18%, 20% will be red and yellow, while when the zinc content is 20%, 30% will be brown and yellow.

.When cutting the copper pipe of air conditioner, use tools such as clamps to fix the copper bar and then cut it, rather than fixing it by hand, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place, and then processed again after cooling,Cage wooden boxBronze plate, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, the global mining industry will rise again and the W-shaped trend will fully emerge. In the second half of the year, there were signs of stabilizing and rebounding. In terms of the macro factors affecting the bulk commodities, the factors affecting the European market of tinned copper bars have gradually weakened, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, products including aluminum, zinc and other products have also rebounded. Only nickel, a basic metal product, has remained weak.

The medical copper tube 6 is superior to the exterior wall hanging plate decorative building materials. It will be affected by microorganisms in the air all year round accelerating the loss of its service life. 7 If the wall interface is not properly treated, the board surface also needs to be treated with interface mortar, otherwise it will cause local hollowing of the insulation layer. How to protect the medical copper tube during installation? The medical copper pipe shall be installed in strict accordance with the installation requirements, the construction process must be strictly required, and do not place heavy objects on the surface.

The price can be changed, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, which was in disorder; Before ten o'clock it was not as expected, and users were very cautious in purchasing; Around 11:00, the surrounding markets became loose and the price was low. High hanging, low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping& after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, the spot price rose, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, and the shipment was not much. Judging from the transaction in the morning, the selling price of leading resources rose generally. Among the resources in Kuti, the base price of t2 copper tube was 5050 yuan/ton, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions, few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, and the purchasing enthusiasm is not high. According to traders' feedback, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.

The degreased copper tube is made of oxygen free copper rod, which has good processing characteristics and can be punched, bent and other process design requirements. The surface can be subject to anti-corrosion treatment such as nickel plating, tin plating, zinc plating, etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin, and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, charging pile, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe, so as long as it is used correctly, there is no need to worry about safety. When choosing to decorate the house, the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and more than 99% of the water will disappear after entering the degreased copper tube for 5 hours. This biological characteristic is that there is a small amount of copper ions dissolved in water in the degreased copper tube, and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer, which can resist extreme weather and is suitable for the long-term surface of metal materials. The actual effect of salt and water corrosion resistance is good. The copper bar tin plating can prevent the air oxidation of the copper bar and the connection surface of the copper bar. In addition, the melting of metal tin and copper will produce aluminum alloy, which will improve the adhesion of copper strip coating. In addition, the conductivity of metal tin is good. The purpose of copper and tin plating: effectively prevent copper from becoming verdant due to moisture, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times, which greatly increases the service life of the copper and plays a considerable role in protecting the copper. The of tinned metal surface treatment on copper bar is to avoid air oxidation. As the air in industrial production air, marine climate or cold air is easy to turn black or produce copper green when oxidized, the copper bar surface shall be tinned for the total area, the resistance and conductivity of the steel bar lap surface.With the continuous development of industry, the demand for plastic coated copper tubes is gradually increasing. Then how to apply wood grain paint on alloy pipes. Wood like paint is a kind of wood like paint. It is used for spraying plastic coated copper pipe and its process flow. Plastic coated copper pipe is mainly used to manufacture high-pressure alloy pipe for heating surface of water tube boiler with high pressure and above. In the morning market, the mainstream spot price quoted by Lianzhong was 7900-7950 yuan/ton, and the tax inclusive base price quoted by Hongwang and Chengde was 8070-8150 yuan/ton. On a month on month basis, part of the producing areas recalled 50 yuan, and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP,Cage wooden box310s stainless steel pipe, UHP and subcritical power plant boilers. Third, large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

If the environment is wet, it will aggravate the corrosion of copper pipes. Oxygen in water causes corrosion.

However, it may cause recoverable temporary damage to people who have been away from these radioactive sources for a long time. The DC brushless motor with small volume and large power is adopted, which can operate without fault for a long time even if it is opened or closed. Target There will be no sharp decline in the price of copper tubes in Linyi at the end of the month. The price of plastic coated copper pipe will continue. Pop up the position line and line, select PVD chromium nitride ring and molybdenum spraying ring as the matching materials for the plastic coated copper pipe, adhere to the wear form condition simulation criteria of the sample test, use the self-developed opposed reciprocating wear tester, carry out the load level test, wear test lean oil test, and research the load. As for the corrugated process of the finished plastic coated copper pipe as claimed in claim 1, the radiation source for the engineering design of the integrated rigid flexible connection plastic coated copper pipe belongs to the low hazard source. Basically, it will not cause artificial damage. The basic principle of the foundation of the integral rigid flexible connection plastic coated copper pipe sluice discussed the influence of process parameters and heat treatment process on the microstructure, phase distribution and mechanical properties of the alloy, the pipe shed shall sweep and clean the hole with drill bit or high-pressure air, and the scum in the hole shall be removed, Ensure the aperture (The hole diameter shall not be less than 127cm, and the hole depth shall meet the requirements to prevent hole plugging. Most of the seamless steel pipes produced now are hot-rolled. Because of the high temperature, the deformation resistance is relatively small, and generally the steel plate is used for rolling. In this operation, the detailed thickness of the steel plate shall also be considered. If it is about the harmful elements with relatively low accuracy requirements, plastic coated copper pipes must be required. The pipe shed can be installed, extended section by section, and What does plastic coated copper pipe with a diameter of 1 reflect in life when the weld length is added to 30 for the joint steel pipe of the pipe extension joint? Plastic coated copper pipe can also produce welded pipes with different pipe diameters from billets of the same width. However, it can be compared with straight seam pipes of the same length. The rental production rate is low.

Finance Department.The medical copper tube 6 is superior to the exterior wall hanging plate decorative building materials. It will be affected by microorganisms in the air all year round, the board surface also needs to be treated with interface mortar, otherwise it will cause local hollowing of the insulation layer. How to protect the medical copper tube during installation? The medical copper pipe shall be installed in strict accordance with the installation requirements, the construction process must be strictly required, and the later maintenance work must be done well. 1 Place it in the rainproof shed, and do not place heavy objects on the surface.

The selection of medical copper tube table, these problems are natural.

Attention shall be paid to the purchase of red copper pipe in order to study the distribution law of pipeline crack stress field under internal pressure. The simulation ysis and experimental verification are carried out for pipes with cracks of different shapes, different directions, different internal pressures and different sizes. The results show that the stress at the crack tip is much greater than that at the crack center. The crack shape has little effect on the stress. With the increase of the included angle between the crack direction and the pipe axis, the stress at the crack tip first increases and then decreases. With the increase of the pipe internal pressure, crack depth, and crack length, the stress at the crack tip increases linearly. Among them, the effect of crack length on the stress at the crack tip is smaller than that of internal pressure and crack depth. During the construction and operation of long-distance pipeline, due to the influence of pipe manufacturing defects, welding defects, internal and external loads, stress concentration, corrosion defects and other factors, which is the most dangerous defect of long-distance pipeline and the main reason for pipeline failure. At present, pipeline cracks are mainly determined by internal testing and non-destructive testing after excavation. Among them, ultrasonic internal testing has a good identification rate for cracks with a length of more than 25 mm, a depth of more than 1 mm in the base metal or a depth of more than 2 mm in the weld; Magnetic flux leakage internal detection has a certain detection rate for cracks with opening more than 0.25mm, but it is difficult to identify and quantify. In NDT, penetration, eddy current and radiographic methods have high detection and identification rate. The generation and propagation of cracks will cause local stress concentration in the pipeline, which is prone to brittle fracture, fatigue damage, corrosion damage and other failure phenomena, seriously affecting the service performance and reliability of long-distance pipeline. In this paper, the influence of crack shape, direction and size on the stress at the crack tip is yzed by studying the stress field distribution law of copper pipe cracks, which provides a reference for the prevention and control of pipe cracks. What problems will be encountered in the production of copper tubes. The production of copper pipe includes four steps: welding, forming, inspection and pipe expansion.

However, it may cause recoverable temporary damage to people who have been away from these radioactive sources for a long time. The DC brushless motor with small volume and large power is adopted, which can operate without fault for a long time even if it is opened or closed. Target There will be no sharp decline in the price of copper tubes in Linyi at the end of the month. The price of plastic coated copper pipe will continue. Pop up the position line and line, select PVD chromium nitride ring and molybdenum spraying ring as the matching materials for the plastic coated copper pipe, adhere to the wear form condition simulation criteria of the sample test, use the self-developed opposed reciprocating wear tester, carry out the load level test, wear test, lean oil test, and research the load. As for the corrugated process of the finished plastic coated copper pipe as claimed in claim 1, the radiation source for the engineering design of the integrated rigid flexible connection plastic coated copper pipe belongs to the low hazard source. Basically, it will not cause artificial damage. The basic principle of the foundation of the integral rigid flexible connection plastic coated copper pipe sluice discussed the influence of process parameters and heat treatment process on the microstructure, and obtained some important research results. The number of joints of steel pipes and plastic coated copper pipes on the same section shall not exceed 50% of the number of pipes. Before installation, the pipe shed shall sweep and clean the hole with drill bit or high-pressure air, and the scum in the hole shall be removed, Ensure the aperture (The hole diameter shall not be less than 127cm, and the hole depth shall meet the requirements to prevent hole plugging. Most of the seamless steel pipes produced now are hot-rolled. Because of the high temperature, the deformation resistance is relatively small, and generally the steel plate is used for rolling. In this operation, the detailed thickness of the steel plate shall also be considered. If it is about the harmful elements with relatively low accuracy requirements, plastic coated copper pipes must be required. The pipe shed can be installed, extended section by section, and What does plastic coated copper pipe with a diameter of 1 reflect in life when the weld length is added to 30 for the joint steel pipe of the pipe extension joint? Plastic coated copper pipe can also produce welded pipes with different pipe diameters from billets of the same width. However, it can be compared with straight seam pipes of the same length. The rental production rate is low.

Quality risk.Manufacture gear, shaft sleeve, worm gear and other high-strength wear-resistant parts and high corrosion resistance elastic components. Key points of semi continuous casting process for copper tube: The copper tube has strong air absorption, easy oxidation and slag formation, large solidification shrinkage, poor thermal conductivity and other casting properties, and poor casting performance; Before casting, some alkaline earth metal compounds, such as Na3A lF6 and NaF mixture are used as slag removers to purify the copper liquid, which is effective for improving the purity of liquid metals and the crystal structure of ingots. The pouring temperature of copper pipes is generally 1120~1180 ℃, and the pouring temperature of large-sized ingots is generally lower. The casting speed of the copper tube is low, and the metal level in the mold can be cast in an open flow manner without any protection; The melt needs to enter the mold through the hole at the bottom of the funnel. The design of funnel aperture should meet two conditions at the same time: one is to ensure the flow matching the casting speed; Second, ensure that the liquid level in the funnel is always kept at a certain height, so that the scum on the liquid level cannot flow into the crystallizer from the funnel hole; The copper tube ingot is easy to produce air holes and concentrated shrinkage cavities. At the end of pouring, the joint coating must be carefully carried out to avoid concentrated shrinkage cavities in the ingot. The red copper tube is a bar shaped object made of copper and zinc alloy, named after its yellow color. Copper content is 56%~68% brass, and its melting point is 934967 degrees. Brass has good mechanical properties and wear resistance, and can be used to manufacture precision instruments, ship parts, gun casings, when the zinc content is 18%, 20% will be red and yellow, while when the zinc content is 20%, 30% will be brown and yellow.

Common defects in copper strip production?

The selection of medical copper tube table, these problems are natural.

Cage wooden box.The process flow of plastic coated copper pipe: the settlement price of 904l stainless steel plate is on the high side, and the price is stable. 904l stainless steel plate: last Friday,Cage wooden boxRed copper bar, the steel plant made all the orders. As for the guide price, the market price rose slightly on Monday due to the positive sentiment after the festival. The working efficiency of t2 copper pipe after the expansion from Tuesday to Friday should be the same. Between the upper and lower clamping groove bodies of the alloy pipe to be flared, the end of the alloy pipe to be flared faces the flaring die, extends a certain length (depending on the flaring length), and then drives the upper clamping groove body to move down through the oil cylinder. Then, the flaring hydraulic cylinder drives the flaring die to the alloy pipe, so that the t2 copper pipe flaring die will stretch the alloy pipe port to expand its inner diameter in the alloy pipe port at the front end. The length of flared section can be 20200 mm. How to solve the crack of plastic coated copper pipe? How to solve the common fault of crack in case of improper operation during the construction of plastic coated copper pipe project? If it is not handled in time, there is a serious risk. Therefore, I will carry out practical operations in strict accordance with the engineering construction specifications and requirements related to immediacy, find more practical welding processes and then ensure the welding quality of electric welding. If we continue to develop plastic coated copper pipe materials under such circumstances, we will find that the price difference of plastic coated copper pipe with low-grade anti rust materials is different, and there are many reasons for the price difference. First, there are significant differences in production. Although it is made of stainless steel, the plastic coated copper pipe can be compared with the plastic coated copper pipe on the market.

One of the classification of copper tubes. The common wave shape is a single copper tube. Hyperbolic means that two different arcs overlap on the same surface, that is, starting from different circle centers, draw arcs in two radii. The red copper tube is a module made of double curves designed according to the drawings. The red copper tube is light in weight, good in rigidity and high in strength. The shapes of the red copper tubes processed are different and can be processed into various geometric shapes such as arcs and spheres. It is beautiful, elegant and colorful. Let's talk about the two main methods of processing and forming the copper tube: The hot processing and forming method is to roll the copper tube to a roughly hyperbolic shape, then heat it, then place it on the mold prepared in advance, then slowly beat it with a hammer, finally cut, weld, fold, polish and polish it. The whole process needs to be very careful to ensure the surface quality of the copper tube. This forming method is very suitable for parts with small model and large arc change. When the model size is relatively large and complex, it can be considered to break it into small pieces for forming, and then splice it into large pieces. For such copper pipes, the cost is high and the production period is long. 2 Forming method of roll bending This method is to make some modifications on the roll bending machine, and change one of the shafts into a concave type and the other into a convex type. This method can form a regular copper tube like a sphere with a small processing range, but it has great advantages for copper tubes with small radians. What problems should be paid attention to when designing the hyperboloid copper tube? Everyone knows that the design of the air conditioning copper tube is very important. To achieve the beautiful shape, exquisite workmanship and fashionable personality of the hyperboloid copper tube, first of all, the design is very critical. Some small copper tube companies are not mature enough in design and have not enough design experience so they often have problems in design, Hyperbolic copper tube is very famous for preparing some details that we should pay attention to in the design. The sculpted copper tube is highly decorative, and the production and processing technology of hyperbolic shaped copper tube is relatively complex. Copper tube products with strong aesthetics. According to the design requirements different shapes need to be molded for the sculpted copper tube, so the production process of sculpted aluminum veneer is relatively complex.

When I need to use more quantity what are the factors that cause the surface corrosion of copper tubes. Introduce the factors that cause the surface corrosion of copper tubes. Surface pollution: The oil, dust, acid, alkali, salt, etc. attached to the surface of the workpiece will be converted into corrosion medium under certain conditions, which will react with some components in the stainless steel parts to produce chemical corrosion and rust.