Hamburg AltonaSimple cargo elevator lifting cargo elevatorThe operation is simple and can be designed

two wheel traction, self driving, and car modification.

Corrosion prevention measures for the body of aerial work vehicles Attention to small scratches The paint surface of aerial work vehicles often corrodes. In addition to common collisions, scratches, and small rocks on the drive tire, there can also be a paint peeling point that can cause a small rust over time. Because most of these scars are small and easy to ignore. Therefore, regularly inspect the engine compartment lid and surrounding areas, and once found, go to a professional beauty shop for processing in a timely manner.

Hamburg Altona.'The sinking of a cargo elevator is a phenomenon where the table surface drops due to gravity after a certain period of time after rising to a specified position. Of course, this problem must be abnormal, so how can we solve it?'? The first step is to find the reason, and the following editor summarizes the ultimate solution.

Before installing the elevator, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of each part connecting the motor and the elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.

.Walking: assisted self-propelled,Hamburg AltonaFixed guide rail lifting cargo elevator, and car modification.

When a cargo elevator fails self driving, it should be repaired by professional personnel. It is not allowed to modify the cargo elevator without permission.

The hydraulic lifting platform can be divided into four wheeled mobile type, two wheeled traction type, vehicle type, auxiliary self-propelled type, and the lifting height varies from a meter to 1 meter.

Test the goods elevator every day to see if it can operate normally.

Replace with new oil and do not intermittently use the old oil, otherwise the moving parts in the system will accelerate wear.

Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten with the hexagon socket. After that, remove the motor shaft key.

Inspection standard.Before connecting the motor to the elevator,Hamburg AltonaFixed simple lifting cargo elevator, the elevator manufacturer should first make the motor shaft keyway perpendicular to the tightening bolt. To ensure uniform stress, first screw on the mounting bolts at any diagonal position, but do not tighten them. Then screw on the other two mounting bolts at diagonal positions and then tighten the four mounting bolts one by one. After that, tighten the tightening bolts. All tightening bolts shall be fixed with a torque wrench according to the indicated fixed torque data, and the use of elevators and lifting platforms shall be checked

Is the water cooling and air cooling of the hydraulic station the same?

It is strictly prohibited for personnel to climb up and down the floors by using the goods elevator privately.

Large logistics warehousing equipment service company with guaranteed prices and guaranteed services, directly operated by the manufacturer. Because fixed elevators are mechanical equipment, the quality and performance of the product are good. Do not accept products from some manufacturers that do not meet the quality standards, in order to avoid some safety hazards in use.

For more, please check.Carefully prepare a special construction plan for installation and construction, and provide safety technical disclosure to installation personnel.

Failure Analysis of Mobile Elevator

Systems: explosion-proof electronic control system, remote control system, PIC system.

Hamburg Altona.In addition to having a fixed mode, there are also types of mobile elevators. As the name implies, it is a combination of lifting equipment and on-board systems. This type of lifting equipment is very flexible to move,Hamburg AltonaElevator enterprise, and of course, it is better to use it. For example, there are such lifting equipment in airports, and stations or stadiums may also be equipped with such equipment as it can be moved by itself, The scope of work is not limited to a certain place, but can be used wherever lifting operations are required. For example, some advertisements are relatively high in height. At this time, mobile lifting equipment can be used to send billboards or staff to a designated height for work. This type of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is the use of hydraulic oil to drive to achieve a specified height. The electric mode is driven by a motor or tooth to lift to a certain height. However, currently, hydraulic lifting platforms are more widely used.

Different. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)

Many people believe that the mechanical strength of the elevator itself is relatively high when using the elevator, so the installation method specified in the manual is not strictly followed during the installation process. However, this can lead to increased wear of parts and inflexibility in operation. In addition, it is necessary to pay attention to the installation precautions corresponding to the working environment and not be careless. Correct installation, use, and maintenance of the elevator are important steps to ensure the normal operation of mechanical equipment. Therefore, when installing the elevator, please be sure to carefully assemble and use it in strict accordance with the following installation and use related matters.