LanceElectric 
LanceSix degre
LanceElectric Fixed loading and unloading bridge: The fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles can move and load goods in batches inside the truck. Only one person can work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.
Using Help | Updating Logs | Original Software | Daily Software
Lance.To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.
Regardless of the type of lifting platform used, people are more concerned about the stability during use. Because the stability not only affects the actual use effect but also has varying degrees of impact on the safety during use, it is necessary to pay appropriate attention. The same applies when using fixed loading and unloading platforms, but many times the stability of this type of platform can be trusted. The reason for saying this is because the manufacturer has taken this issue into account during production and manufacturing, and the following aspects are taken to avoid this situation.
.The brakes of each mechanism should be regularly checked and adjusted for the clearance between the brake pads and brake wheels to ensure flexibility and reliability. There should be no dirt on the friction surface. If there is dirt,LanceElectric fixed hydraulic lifting platform, it must be cleaned with gasoline or rare materials.
Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors, wiring and oil cylinder once a week to avoid dust and debris affecting normal operation.
After working for 10000 hours,LanceHydraulic freight platform, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, a straight top platform, or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, open platforms do not have doors. The electrical part is composed of power, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings, pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, door electromechanical interlocking, rupture valves, emergency switches, there are many details that need to be noted, such as placing it on a flat surface during use to prevent tipping during work. In addition, what are the precautions for using electric lifting platforms?
Leading spaces in blank lines Full width: Font size: Replace: Replace
Inspection requirements.Secondly, the maintenance of the guide rail type hydraulic lifting platform is also very simple, using oil cylinders and chain transmission, with very few moving components, so the maintenance workload is not very high. Moreover, this type of lifting cargo elevator has a very compact structure and uses fewer bearings, resulting in a longer service life.
Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame,LanceHydraulic flipping platform, scissors, and oil cylinder once a week to avoid dust and debris affecting normal operation.
After 5000 hours of operation of the elevator, repair the mechanical and electrical systems.
The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform, or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.
Design brand.Tail signature:
The characteristics of hydraulic lifting platforms are obvious, such as their relatively light overall weight and good maneuverability, allowing even a single person to operate, making them relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, attention should also be paid to the structure of the hydraulic lifting platform to ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
Safety protection components, in order to ensure safety production it is essential to install a lifting platform for proper protection. The main protective accessories include safety belts, guardrails, protective covers, platform stairs, etc.
Lance.There are many types of materials that manufacturers can use in the manufacturing process of the same lifting equipment, but the lifting equipment manufactured from different materials will also be different. The material used by manufacturers in the manufacturing process of aluminum alloy elevators is aluminum alloy with very high strength. It should be noted that this type of material itself has many advantages, for many people, the reason why they choose this type of lifting equipment is also closely related to its marketing highlights.
When we use hydraulic elevators in our daily lives, we need to regularly inspect and maintain them. This not only extends the lifespan of the hydraulic elevators, but also allows them to exert greater power in their work. For example, the transmission part requires sufficient oil, maintained, or replaced. Mechanical bolts, especially those that frequently vibrate, such as rotating supports and lifting arm connecting bolts, must be tightened or replaced immediately when they become loose. Next, the editor will introduce how hydraulic elevators should be maintained.
The drive motor can stop the movement of the rack on the pillar.