San JoseHouseh
San JoseHydrau
San JoseCustomThe noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, and the air or oil pipe is on the oil surface the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)
San Jose.In case of strong wind of level 6 or above, rainstorm, thunder, fog and other bad weather, the work at heights in the open air shall be stopped at the boarding bridge.
Therefore, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.
.The installation personnel should have the qualification for installing hydraulic cargo elevators, carefully implement the special construction plan for installation and construction, and provide safety technical disclosure to the installation personnel for technical design.
Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
Hydraulic lifting table: the hydraulic lifting table is widely used in various industrial enterprises and production lines such as automobile, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operation heights, and can be equipped with various table forms (such as ball, roller, rotary table, steering, telescoping), and with various ways (separate, linkage, explosion-proof), it has stable and accurate lifting, frequent starting The characteristics of large load capacity effectively solve various lifting and lowering difficulties in industrial enterprises, making production operations smooth.
Remove the hydraulic oil tank filler cap, filter cover inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap,San JoseHydraulic cylinder lifting platform, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.
In on-site hydraulic elevators, it is difficult to detect the rising position, middle position, impact noise, and oil film leakage of hydraulic cylinders. Field observations have shown that the excessive lifting speed of the hydraulic cylinder has led to an increase in failure rate seriously affecting production efficiency. The unstable hydraulic lifting requires an analysis of the hydraulic oil flow rate. Hydraulic pressing oil has poor quality and contains a large amount of impurities, which can also prevent slow and unstable lifting. In addition there are other reasons: lifting the composition of the hydraulic ring. Oil pump, safety valve, directional valve, directional valve, one-way throttle valve (without throttling) and lifting cylinder.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
Product line.Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.
Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.
There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.
Mobile is a type of cargo heavy machinery equipment with good adjustment reliability and wide application fields, suitable for automated production lines
Scheme customization.When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.
In addition, in areas with large or high waves, in order to facilitate the arrangement and prevent the hydraulic cargo elevator cylinder from being eroded by waves, a lifting structure should be selected to determine the installation position of the oil shoulder, as the lifting point of the bridge is not in a straight line during the lifting process. Therefore, during the lifting process of the cylinder, the connection between the two ends of the cylinder and other components must be hinged in the same square. In addition, the installation of the hydraulic cargo elevator cylinder must also be determined through comparison and calculation, whether it is the tail lifting ear type,San JoseHydraulic lifting platform, the middle pin shaft type, or the head pin shaft type. The main advantage is that the effective area of the cylinder is large, and the overall installation height is low. The disadvantage is that if the cylinder stroke is large, there may be stability issues with the cylinder, and the cylinder layout may be difficult. The main advantage of the hydraulic cargo elevator lifting mechanism is that it does not have a stable transmission installation frame for height measurement. Therefore, this form can be considered in places with large drops. The sudden deafness oil type on the head can reduce the installation height, but if it is too large, the oil cylinder will experience an increase in force due to the lifting height. Moreover, the higher the lifting height, the faster the increase in force, which is not suitable for the use of the oil cylinder. Therefore, when it is too large, the head pin type is not suitable. In order to comprehensively consider the height of the installation bracket and the force on the oil cylinder during the lifting process, an intermediate installation method can be considered, and the installation position can be set at an appropriate height according to calculations.
When installing, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.
San Jose.Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.
Wholesale manufacturers of hydraulic cargo elevators have found that the market demand for hydraulic cargo elevators is also increasing. More importantly, some cargo loading and unloading work, as well as decoration, hotels, logistics, supermarkets, etc., are commonly used in these situations, especially in the decoration industry. I have seen many decoration companies use small hydraulic cargo elevators, which are also specially processed and manufactured, and have some differences from the hydraulic cargo elevators we often see. There are significant differences in structure, shape lifting speed, and height, some only 2 meters, and do not require many materials. He mainly promotes people, not goods, and rarely promotes goods, so the load is small, but not inferior to the use of other hydraulic cargo elevators. He is stable, safe, interpretable, and durable enough to make hydraulic cargo elevators a good helper in the decoration industry. The function of hydraulic cargo elevators is gradually improving with our needs, and the properties we require are different. Wholesale manufacturers of hydraulic cargo elevators also manufacture according to our requirements.
When installing, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.