MILUSMicro hyd
MILUSHydraulic
MILUSCylinder Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.
Optional configuration of fixed lifting platform: The fixed lifting platform can be equipped with auxiliary devices according to usage requirements, and can be combined in any combination,MILUSHydraulic lifting platform, such as the safety protection device of the fixed lifting platform; Electrical methods; Form of work platform; Power form, etc. The correct selection of various configurations maximizes the functionality of the lifting platform and achieves effective use.
MILUS.In winter, when working outdoors at heights below minus 10 degrees Celsius, heating rest areas should be set up near the construction area if necessary. Heating equipment should be managed by dedicated personnel and attention should be paid to fire prevention.
An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.
.Users should arrange dedicated personnel to operate hydraulic elevators, formulate usage details and safety precautions for hydraulic elevators based on their own situation, and hang them on the
There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
Surface paint quality: The paint should be smooth and flat, have uniform color, no bubbles no cracks, and there should be no wrinkles, pits, paint leakage, and sagging.
When encountering signs of overheating in the electric motor, it is necessary to park the car in a timely manner, clean the problem and continue running. The motor bearings should be smooth and outstanding.
If working on a grid like platform,MILUSHydraulic lifting platform frame, wooden boards should be laid to prevent tools and equipment from falling.
Reason: The lowering speed valve is out of adjustment. Cleaning method: If the lowering speed valve is adjusted, and if the adjustment is ineffective, replace it with a new valve.
Quality risk.If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.
There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.
The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.
The hydraulic pump produces noise. When the hydraulic elevator rises, the hydraulic pump runs at high speed. If there is a problem with the gears or bearings of the hydraulic pump, which causes periodic changes in the hydraulic system pressure, it will also cause resonance in the hydraulic system and generate noise.
Potential development.Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, we will analyze for everyone. According to the market survey and understanding conducted by the editor of hydraulic freight elevator manufacturers, many customers choose hydraulic elevators instead of elevators due to the following reasons: narrow transportation location, which cannot meet the requirements of elevators; Unable to excavate the elevator shaft at the working location; Elevators are expensive and difficult to meet their needs.
Hydraulic cargo elevators have been used in some high-altitude operations in recent years, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes, becoming a better choice for some high-altitude operations. However, there are still certain limitations such as height and improving the quality of goods, which have certain constraints.
MILUS.When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5, please stop using it; When the lifting height exceeds 10 meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed,MILUSScissor fork hydraulic lifting platform, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.
The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.