ELFORD10 ton mobile boarding bridgeFeatures and scope of application

Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, if there is insufficient oil and add oil. If there is any abnormal noise or rapid temperature rise,ELFORDFixed boarding bridge, repair it in a timely manner

The lifespan can reach twice that of the tires on the rigid suspension boarding bridge. In addition, tires that do not use self steering cars wear three to four times faster. It is obvious that the additional cost incurred by using the self steering boarding bridge will soon be compensated. Semi trailers using self steering boarding bridges are flexible in operation and require a narrow road width when turning, suitable for various occasions. Experiments have shown that the turning radius of a semi trailer with the same body length and load can be reduced by about 10% when using a self steering car.

ELFORD.The fixed boarding bridge of the service platform is immediately installed on the outer edge of the unloaded service platform during the entire installation process. When applied, there is no need to excavate or pre bury the indoor space of tunnel construction on the loading and unloading platform, and most of the buildings do not need to be modified in terms of structure.

A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, tractors, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, which can easily and conveniently achieve traction movement.

.The equipped brake pads can effectively prevent the shifting of the boarding bridge during truck loading and unloading.

Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, if there is insufficient oil, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely manner

Adopting anti slip patterned steel plates, the platform has good anti slip performance.

Long term promotion to the axle factory, sand holes, and other conditions. Generally, there is a problem with the casting, which is the quality of the oil cylinder itself. At this time, it is necessary to find a manufacturer to replace the new boarding bridge. Normally, this situation does not occur in the casting oil cylinder. The above two reasons are due to the occurrence of excessive oil leakage and frequent inspections should be conducted in these two areas. Hydraulic loading and unloading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods during the application process. The height adjustment function of the equipment makes the bridge in the middle of the truck guide sufficient to be built. Lifting platforms, trucks, it is necessary to operate it in a safe manner. Unfamiliar personnel should not do so. During the operation, do not stand bystanders around. Be sure to carry the load according to the rated load, and do not overload or deviate. The rated load of the fixed hydraulic boarding bridge specified by the manufacturer is the total weight of the loaded goods and forklifts, not the weight of the goods alone. This is something that customers and friends should know. If there is detachment or deformation of the boarding bridge, please do not use it to avoid serious accidents. The boarding bridge is mainly an auxiliary device for loading and unloading goods, which greatly improves the loading and unloading power (referring to the amount of work done by objects in a unit of time), and is something that logistics companies (Company) cannot do less. If the power of the boarding bridge operation (zuò yì) is to be durable,ELFORDContainer forklift boarding bridge, no problems can appear during the operation. Perhaps the problems can be dealt with in a timely manner. Regarding identifying the cause of the hydraulic system problem of the boarding bridge, It is beneficial for us to use the boarding bridge correctly and provide homework

Highly recommended.The boarding bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles can move and load goods in bulk inside the truck. Only one person needs to work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.

A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.

All comply with relevant national and industry technical standards, and customer satisfaction has always been our eternal pursuit. The fully automatic lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail type, folding arm lifting, and curved arm type. Fixed types include scissor fork type lifting cargo elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms. The mobile hydraulic loading bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is an auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. With the help of a mobile loading bridge, forklifts can directly enter the interior of car containers for bulk loading and unloading operations. The car mounted hedge trimmer improves the trimming quality, saves labor, improves work efficiency, and has a 40 times higher rate than manual trimming, without any safety hazards; Can form different plant shapes. Used for pruning road greening plants. The green belt trimming machine mainly rotates the head side, and bottom films to complete the trimming of the top, and lawn of the green belt. The machine has a simple appearance, is very convenient to move, is easy to operate, and can adjust the height freely. It can also trim the top, side, and lawn of the green belt at the same time, saving a lot of manpower. The hydraulic cargo elevator must be installed in a closed wellbore environment, and the actual situation of the wellbore determines the specifications and dimensions of the final hydraulic cargo elevator. This includes the width and depth of the shaft as well as the conditions of the pit and machine room. Hydraulic oil is an important operating medium for fixed hydraulic boarding bridges, which is abstractly compared to the quality of blood hydraulic oil in fixed hydraulic boarding bridges, which indirectly affects the service life of hydraulic lifting channels. Pure and impure hydraulic oil is the key to ensuring the operation of fixed hydraulic boarding bridges. When making a purchase, it is important to carefully reflect, observe the color, smell the scent, and prevent internal environmental purification when storing together.

Process inspection.There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.

The guide sleeve has air holes, sand holes, shrinkage, and other conditions. Generally, there is a problem with the casting,ELFORDHydraulic fixed boarding axle, which is the quality of the oil cylinder itself. At this time, it is necessary to find a manufacturer to replace the new boarding bridge. Normally, this situation does not occur in the casting oil cylinder. The above two reasons are due to the occurrence of excessive oil leakage, and frequent inspections should be conducted in these two areas. Hydraulic loading and unloading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods during the application process. The height adjustment function of the equipment makes the bridge in the middle of the truck guide sufficient to be built. Lifting platforms, trucks, and hydraulic loading and unloading bridges are commonly used cargo loading and unloading equipment.

There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.

ELFORD.The adjustable length of the cable chain can easily hook the truck, ensuring that the boarding bridge and truck always fit tightly.

Anti collision block: This device can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. Platform with& quot; U& quot; Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability. Professional Tideng Axle Factory quality assurance. Discount activities are underway, welcome new and old customers to come for consultation

Product features: Fully hydraulic drive, easy to operate and reliable to operate.