LuanchengAlumi
LuanchengScissFor hydraulic cylinders in hydraulic elevators, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.
Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
Luancheng.Compare the measurement curves and then go to the variable displacement pump or variable speed motor. Long term targeting all types of high-priced elevator manufacturers nationwide with reasonable prices and comprehensive services, we have gained recognition from our customers
After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.
.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract,LuanchengHydraulic cylinder lifting platform, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.
When using hydraulic elevators, the main causes of noise are mechanical mechanism failures hydraulic system failures, etc. Today electrical equipment or component failures, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.
After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
Separate: Loading and unloading on different platforms.
Therefore, maintaining the hydraulic cylinder is an important part of the entire hydraulic system maintenance. In addition, hydraulic cylinders are equivalent to the heart of the hydraulic system, making it difficult to repair heart problems. Therefore, maintenance of hydraulic cylinders should be cautious. Professional elevator manufacturers have advanced technology, more affordable prices, and more discounts. Welcome to consult
A hydraulic elevator is a type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
resources.Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap,Luancheng15 meter hydraulic lifting platform, first remove the soil around the tank cap loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.
When using hydraulic elevators, frequent inspections and maintenance should be carried out which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).
Remember not to overload, overload is the root cause of many faults.
Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.
Hydraulic cargo elevator sinking refers to the lifting of the cargo elevator equipment to a designated position, and after a period of time, the entire table surface will automatically descend by a certain distance under its own weight. The phenomenon of hydraulic cargo elevators naturally descending during the leveling process. such
The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms.
Luancheng.New reference wiring diagram 2. Elevator leg noise. Mobile elevators should open the legs before operation. In this case, if the legs lack butter, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.