KilkennyHydrau
KilkennyHydrauHydraulic lifting platform is a non scissor type hydraulic lifting platform and is also a widely used vertical transportation equipment for goods, among which the commonly used is the guide rail hydraulic lifting platform. Mainly driven by electric motors and oil pumps, heavy chains are driven by oil cylinders to drive the lifting and lowering of hydraulic lifting platforms. It is also widely used for vertical transportation of goods between high-rise buildings. So, what are the advantages and characteristics of guide rail hydraulic lifting platforms?
The product has a sturdy structure, a large load-bearing capacity, smooth lifting, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance, they must hang the elevator to prevent sudden lowering of the platform and causing casualties.
Kilkenny.When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site,KilkennyHydraulic fixed lifting platform, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
.The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform, with manual and automatic doors. Generally forming a door system. The closed or mesh platform door or door system consists of a steel structure, open platforms do not have doors. The electrical part is composed of power, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.
When using the elevator, we should listen for any abnormal noise. If there is any abnormal noise, we should immediately stop using it to avoid serious damage to the elevator.
Secondly, the lifting platform is driven by electrical energy and lifted by the hydraulic system. During operation, it is necessary to avoid irregular operations. To ensure the normal and orderly operation of the lifting platform and achieve the ideal unloading level, timely inspection of various functions is essential.
If hydraulic elevators are used on campus, it can better enhance the safety and security of the campus. For campuses, especially after school every day,KilkennySupply hydraulic lifting platform, there are a large number of parents and there are also safety hazards such as people and cars. Maintaining order in such situations is a good idea.
When a hydraulic lifting platform malfunctions, it is necessary to take time to prepare accordingly. At this time, it is necessary to provide timely feedback or communicate with the manufacturer. If a voltage range is used to detect the hydraulic lifting platform, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, in this case, an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform adopts heavy-duty chain transmission, hydraulic explosion-proof oil pipes, safety devices to prevent overloading, multiple limit switch protection, door and power outage protection, leakage protection, and multi-layer building interaction. Therefore, the safety factor of the guide rail hydraulic lifting platform is still very high, much higher than that of ordinary platforms.
For project engineering, if the selected construction elevator can ensure the safety of construction workers, of course it can also improve the overall work efficiency of the construction. Therefore, there are many manufacturers and types of construction elevators on the market, and facing the mixed situation of good and bad, many customers have no choice when choosing. In fact, when choosing elevators, the first thing to pay attention to is their quality, so that they can choose suitable elevators. But now many customers have high requirements for craftsmanship when choosing elevators.
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
Where can I find it?.The pressure lifting platform adopts a double four bar mechanism to achieve the lifting and flipping of the vehicle mounted cargo elevator platform, and a complex self-locking mechanism to achieve automatic opening and closing of the baffle. In order to reduce driving force, multiple sets of pulleys are used to achieve motion transmission and smooth movement on both sides of the lifting device. The hydraulic lifting platform adopts a hydraulic power unit transmission method,KilkennyScissor type hydraulic platform, making the lifting more stable and the service life longer.
In this situation, it is necessary to regularly check all wires and cables used to ensure that there is no damage. When there is wrapping or damage, the parts should be replaced in a timely manner. I believe many people have encountered overheating in electric motors. In this case, it is necessary to stop the motor in a timely manner, and then troubleshoot the problem before continuing to use it. This way the motor shaft can be used and the effect is good.
Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
Kilkenny.The above detailed introduction I believe everyone has a certain understanding of elevator selection, so that they can have a clear goal when choosing, and then choose the elevator that is suitable for customers.
Fixed loading and unloading bridge: The fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, improve work efficiency, and obtain greater economic benefits.
When the motor overheats, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.