MazetourHydraulic lifting platformIndustry leader

The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.

Remove the hydraulic oil tank filler cap, filter cover, inspection hole, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.

Mazetour.What are the requirements for the pit? This type of cargo elevator only needs 15-30 centimeters and does not require too much space. The installation of scissor type hydraulic cargo elevators is different from that of guide rail type hydraulic cargo elevators. The scissor lift cargo elevator has a large load-bearing capacity, and the pit depth needs to be set at around 40-70 centimeters. It can also be designed according to customer on-site needs.

Lifting mechanism: The workbench should be ensured to rise and fall smoothly, and there should be no jumping lifting phenomenon. All moving parts should be flexible when moving,MazetourHydraulic electric lifting platform, and there should be no jamming devices. The lifting system of the elevator is divided into electric or manual hydraulic systems, and there should be no leakage at all components, pipelines, and joints.

.Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.

The speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits, high-speed circuits, and speed switching circuits.

Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.

Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

For example,MazetourElectric hydraulic fixed lifting platform,MazetourHydraulic lifting platform Electric lifting platform, setting anti fall and interaction can achieve good usage effects. This product is mainly used in various enterprise factories.

Volume speed control circuit: Speed control is achieved by adjusting the displacement of a variable pump or variable motor.

Manufacturing cost.Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point it is necessary to exhaust the air in a timely manner.

Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.

Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.

Recommendation and consultation.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.

Firstly, rust prevention is necessary. Because the part of the hydraulic cylinder needs to extend out of the cylinder during operation, it will naturally be corroded by oxides and acidic gases. This requires us to apply an appropriate amount of grease to protect it from erosion as a weight component. If we change the oil, we must open the box and use it for a long time to prevent the hydraulic cylinder from being used for a long time. In the operation of hydraulic cylinders the speed should be appropriate and should not exceed 2m/s to extend the service life of the hydraulic cylinder. In addition, in order to protect the mechanism and safety, it is very important to install buffer devices internally to protect the hydraulic cylinder. The greater the pressure of the protective hydraulic cylinder, the heavier the load, and the greater its pressure. A specialized product manufacturing enterprise that integrates research and development, as well as service. A long-term professional elevator manufacturer

When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.

Mazetour.When the hydraulic oil is insufficient, causing air to enter the hydraulic oil and producing high noise.

Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, there was air in the hydraulic cylinder due to an operational error. Under high pressure it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise