GleevecScissor fork hydraulic lifting platformOffer summary

To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.

Regularly check the operation of each mechanism for normal operation and noise. If any faults are found, the hydraulic cargo elevator wholesale should be promptly eliminated. Otherwise,Gleevec10 meter lifting hydraulic platform, it will affect the use of the guide rail hydraulic lifting platform. When refueling, the hydraulic oil should be filtered and filled, and the refueling tools should be reliable and clean. The hydraulic cargo elevator manufacturer should not remove the filter at the fuel tank filler to improve the refueling speed. Refueling personnel should use clean gloves and work clothes to prevent solid and fiber impurities from falling into the oil.

Gleevec.Hydraulic cargo elevator: Only when the load of the hydraulic guide rail type lifting cargo elevator cannot start working, should the pressure of the hydraulic system be checked. If the pressure is below the normal range, the set value of the relief valve should be adjusted. Professional elevator manufacturers have high pressure resistance,GleevecScissor type hydraulic lifting platform, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation resistance, such as the safety protection device of the fixed lifting platform; Electrical methods; Form of work platform; Power form and can be combined in any combination,GleevecHydraulic cylinder lifting platform, etc. The correct selection of various configurations maximizes the functionality of the lifting platform and achieves effective use.

.The hydraulic pump produces noise. When the hydraulic elevator rises, which causes periodic changes in the hydraulic system pressure, it will also cause resonance in the hydraulic system and generate noise.

Pre install equipment, maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, some require equipment such as forklifts for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.

Each box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.

The main device does not engage. When this fault occurs, check whether the three-phase power supply is normal, whether the internal and external emergency stop button switches, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.

There are two installation methods for hydraulic freight elevator oil cylinders: jacking and lifting. The difference between jacking and lifting is that the placement direction of the oil cylinder is opposite, which is a qualitative problem and easy to arrange. The disadvantage is that the effective use of the oil cylinder can lift the same load, and the oil cylinder of the lifting mechanism is much larger than that of the lifting mechanism. Professional elevator manufacturers and other special products, 20 year old brand, with price advantages and guaranteed quality

Pre install equipment maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift some require equipment such as forklifts for installation, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.

Test results.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.

There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.

Volume speed control circuit: Speed control is achieved by adjusting the displacement of a variable pump or variable motor.

The elevator itself has a simple structure and is easy to maintain, also known as hydraulic powered elevators.

Production department.The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.

When working at heights, except for relevant personnel no one is allowed to walk or stay below the workplace. Fencing or other protective devices should be installed below the workplace to prevent falling objects from injuring people.

After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.

Gleevec.Load bearing capacity: The lifting platform is placed on a horizontal support surface, and the workbench is evenly loaded to 125% of the maximum load capacity. After lifting 100 times, each load-bearing component must not have deformation or cracks.

Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.

The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.