Garman LakeMan
Garman LakeFixConsidering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract,Garman LakeType hydraulic lifting platform, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators,Garman LakeIndoor fixed hydraulic lifting platform, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.
Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.
Garman Lake.What are the requirements for the pit? This type of cargo elevator only needs 15-30 centimeters and does not require too much space. The installation of scissor type hydraulic cargo elevators is different from that of guide rail type hydraulic cargo elevators. The scissor lift cargo elevator has a large load-bearing capacity, and the pit depth needs to be set at around 40-70 centimeters. It can also be designed according to customer on-site needs.
If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.
.Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.
When encountering signs of overheating in the electric motor,Garman LakeFreight elevator type hydraulic lifting platform, it is necessary to park the car in a timely manner, clean the problem, and continue running. The motor bearings should be smooth and outstanding.
Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.
Therefore, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.
Cylinder diameter and hydraulic oil flow rate. The speed of the hydraulic lifting device is inversely proportional to the cross-sectional area of the cylinder rod and directly proportional to the flow rate of hydraulic oil. When the hydraulic elevator runs slowly, priority should be given to the hydraulic oil flow angle.
Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.
Free consultation.The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.
Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.
When the hydraulic oil is insufficient the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.
After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.
Excellent service.After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
High altitude work should always use tool bags. Tools with larger boarding bridges should be tied to sturdy components with ropes, and should not be placed randomly to prevent accidents caused by falling from a height.
The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.
Garman Lake.After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.
The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point