MazetourPrice 
MazetourScissoMazetourFixed hydraulic platform,
The product has a sturdy structure, a large load-bearing capacity, smooth lifting, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will tell you about the level
Are there any damages to the wires and cables of the department. We need to quickly bandage and replace the damaged department.
Mazetour.The cleaning of the elevator manufacturer requires that all parts of the elevator should be kept free of oil sludge, dirt and dust, especially the air, fuel and oil filter of the engine should be checked and cleaned according to the specified time to prevent impurities from entering the cylinder and oil passage, so as to accelerate the wear of moving parts. Elevator manufacturers suggest developing some maintenance systems. The regular maintenance system is based on the wear and service life of mechanical components, as well as the wear and tear patterns of oil and liquid. The maintenance system mainly determines the maintenance needs of the machinery based on the operating hours of the machinery, which has also become the planned expected maintenance system.
Before using the machine, the staff should carefully inspect the hydraulic and electrical systems to ensure that there are no leaks or bare leaks before use.
.Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.
In our daily life, hydraulic cargo elevators are increasingly widely used and loved by customers. As a lifting tool, the maintenance of hydraulic cargo elevators should not be careless. Below, the editor will introduce the daily maintenance of hydraulic cargo elevators.
The inconsistent rotation axis of the support rod in the middle of the hydraulic lifting platform results in the lifting platform being unable to function properly,MazetourHydraulic automatic lifting platform, causing serious damage to the platform and causing the table to tilt. Please carefully check that the general shear type high-altitude work platform was not strictly tested for tilt before leaving the factory, and was put into the market, causing many accidents. For small enterprises, they are not very concerned about this aspect of tilt detection, This is also why there are such a large number of lifting equipment with this problem. The problems with the oil cylinder and power unit system are often due to insufficient power and substandard oil cylinder quality, which are also very important issues for enterprises themselves.
Elevator customers all have overloaded use of elevators. Although elevators have a large overload capacity in design, the hidden dangers brought by such use are very large, which can easily cause damage such as oil cylinder roof fall and elevator bracket deformation. So it should be summarized as follows: Maintenance of elevators must be equipped with full-time elevator operators who have undergone on-the-job training, and illegal operation and use are strictly prohibited.
The axle manufacturer's oil cylinder is leaking and the oil cylinder seal is being replaced. The lifting platform does not lower and the lowering valve is malfunctioning. When the lowering button is pressed, check if the lowering valve is energized. If there is no electricity, try to eliminate it; If there is electricity, troubleshoot the lowering valve itself or replace the lowering valve. The lowering valve should be kept clean.
Familiarity with the usage process and without a doubt, this is the first thing to understand. There are two ways to understand it: first, carefully read the user manual provided by the manufacturer when the hydraulic lifting platform leaves the factory; The second is the equipment that needs to be installed. A professional installation technician will be dispatched to install the hydraulic lifting platform. After the installation is completed, relevant users will be trained on the operating process and safety precautions of the hydraulic lifting platform, and some maintenance matters in the future will also be explained; What should be paid attention to during the running-in period when using hydraulic lifting platforms? Check the wear of components. For newly processed and assembled components, there may be subtle deviations in shape and size that require a period of time for running-in. Therefore, during the running-in period, it is necessary to pay attention to whether there is any rapid wear. If there is any, the manufacturer of the hydraulic lifting platform should handle it in a timely manner to avoid equipment failure; Work between the pins and bearings to ensure that they are not worn and add some engine oil or grease appropriately; Confirm if there is any noise during the running-in period. If it is found that the hydraulic lifting platform is noisy during operation, there is no need to worry in the early stage. If there are no major problems, the noise will naturally disappear. However, if there is noise for a long time and no signs of fading, please make sure to promptly produce it and solve the problem; Regularly check if the components are loose. Before use, check if there are any signs of looseness in screws, nuts, retaining rings, oil pipe joints, etc. If there are any, please reinforce or replace them in a timely manner to avoid accidents.
Credit guarantee.Mobile elevators are generally used in skyscrapers where electric elevators are used, as there is no need to stop midway, so fast elevators are needed. First go to the high-rise sky lobby (high-rise elevator lobby Skylobby) from the ground, and then transfer to the ordinary elevator to the destination. Some new elevators use elevator pre calling systems, while others are set up in the cabin, coupled with its own vibration, the motor collides with other components, resulting in a sound; The joints of each pin shaft are dry, lacking oil, and there is hard friction between the iron parts, which not only damages the components but also produces abnormal noises. Therefore, the editor should emphasize again that timely maintenance and frequent refueling are important; If the hydraulic lifting platform does not rise, there is air in the hydraulic oil. You can open the exhaust hole, add gas, and then tighten it again; Hydraulic oil solidification: replace the hydraulic oil; Oil leakage: Check if there is any oil leakage at the interfaces of each oil pipe. If there is any oil leakage, replace it in a timely manner; Motor reversal: Check for wiring errors; (Manufacturers of hydraulic lifting platforms who do not understand electricity in a timely manner)
The application scenarios of mobile elevators may require several or even dozens of passenger elevators in some office buildings and hospitals. In order to increase the speed efficiency, and usable area of electric elevators, most high-rise buildings will divide electric elevators into arrays, with each group responsible for a portion of the floors, and make different adjustments and scheduling based on the usage mode of different floors at different times.
Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated. For a long time, mainly for transporting people and goods. We can effectively use construction elevators to improve the efficiency of operations and greatly reduce the workload of operators. So and the price is 20% higher than the market value! More than one ton is more expensive!
Trustworthy.Construction elevators are commonly used in industrial or construction sites in our daily lives, how should we inspect the construction site of construction elevators? You know?
The oil filter is severely blocked; The solution is to clean the oil filter or replace the hydraulic oil. Long term lifting scissors fork lift manufacturers and other various brand products, with complete designated products and guaranteed quality
The daily maintenance of guide rail type cargo elevators should ensure that the transmission position where the grease nipple is located needs to be lubricated twice a month. For areas where grease cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.
Mazetour.The reduction gearbox, gearbox, external meshing gear and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table. Professional scissor lift manufacturer with high prices, service, on-site settlement, and honest operation!
The application scenarios of mobile elevators may require several or even dozens of passenger elevators in some office buildings and hospitals. In order to increase the speed, efficiency and usable area of electric elevators, with each group responsible for a portion of the floors,MazetourIndoor hydraulic lifting platform, and make different adjustments and scheduling based on the usage mode of different floors at different times.
The correct construction inspection of the airport is to first inspect the foundation to see if there is any water accumulation and to see if the grounding system meets the requirements. We also need to see how the structural bolts of this frame are tightened, and whether there are any cracks in the welds. We need to set them according to the instructions. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, there are also many safety equipment for elevators.