El PragueSinglWhen the motor connection of the elevator is incorrect, when a coil, coil group, or one phase winding group is connected in reverse, it can cause serious three-phase current imbalance and cause the winding to overheat.
Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator,El PragueFactory cargo elevator elevator, everyone must pay attention to safety.
El Prague.Multi column aluminum alloy lifting platform is widely used for cleaning and circuit maintenance of the top floor of airports, high-speed railway stations, shopping malls, and star hotels. It has a high elevation, low self weight, flexible movement, and simple design.
The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, but do you know how to choose good cables? Below, the editor will summarize how to choose good elevator cables for everyone. Long term improvement of various brand products such as elevator manufacturers, with complete designated products and quality assurance
Curved arm elevator: a lifting device used for high-altitude operations, which can cross obstacles for high-altitude operations. When the platform is lifted to any position, it can operate while walking, with a compact structure and flexible turning. The width of its site can ensure that the equipment enters narrow passages and crowded working areas. The backup power device can operate the work platform to reset, and is a convenient transportation method that can be towed to any place.
Single column aluminum alloy elevator with easily recognizable operation panel, multiple mechanical, electrical, and hydraulic safety protection, and advanced integrated hydraulic electricity
According to different needs, different power modes can be selected, DC power supply single-phase AC power supply, and internal combustion power supply. With manual hydraulic equipment, lifting operations can be carried out in places with power outages or no power supply, and components can be added. When the platform length is insufficient, it can be extended to the required direction, and a necessity for high-altitude safety and civilized production.
The rust prevention work of aerial work vehicles is generally something that needs to be paid attention to when they have not been used for a long time. How should we do anti-corrosion on the body of aerial work vehicles? This is actually a simple matter of not having to spend money on anti-corrosion at the repair station. As long as we car owners use some materials they can find on their own, we can achieve this. At the same time paying attention to driving habits can ensure that high-altitude work vehicles do not rust. Here are a few points for reference.
Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be 40-50 millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.
Variable cost.In addition, it is strictly prohibited to use hammers or other tools during installation to prevent excessive axial or radial force from damaging bearings or gears. Be sure to tighten the installation bolts before tightening the tension bolts. Before installation, clean the anti rust oil on the motor input shaft, positioning boss, and elevator connection parts with gasoline or zinc sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation and to prevent unnecessary wear and tear.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface,El PragueCar mounted scissor lift, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models first install the suspension cage before installing the drive plate).
Walking: assisted self-propelled, two wheel traction, self driving, and car modification.
Hydraulic lifting platforms are widely used in factory maintenance, municipal construction,El Prague16 meter lift truck, and decoration of hotels in industrial and mining enterprises, with reliable quality and perfect performance.
Quality improvement.The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
The anti-corrosion measures for the body of high-altitude work vehicles should pay attention to small scratches. The paint surface of high-altitude work vehicles often corrodes. In addition to common collisions, scratches, and small rocks on the driving tires, there can also be a peeling point, regular inspections should be conducted on the engine hood and surrounding areas. Once discovered, it is necessary to promptly go to a professional beauty shop for processing.
Loose or leaking connection between the oil suction pipe and the gear pump; The solution is to tighten the suction pipe.
El Prague.Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so during the installation process, there is no
Characteristics of hydraulic elevators: Hydraulic lifting platform products are divided into curved arm hydraulic lifting machines, scissor fork hydraulic lifting machines, and straight arm hydraulic elevators according to their working modes. Hydraulic elevator is a replacement product of folding arm elevator (lifting platform) and scissor fork elevator (lifting platform). It can be widely used for the decoration and decoration of stations, docks, airports, hotels, posts and telecommunications, municipal gardens, garages, cleaning companies, public building facades, or the installation and maintenance of power systems, etc. This elevator has the advantages of light weight self-propelled walking, electric starting, self supporting legs, simple operation, large working area, and especially the ability to cross obstacles for high-altitude operations.
Three column aluminum alloy elevator: Three sets of masts support the synchronous lifting of the working platform, and the support structure is the same as that of a single masted platform, with super large load capacity and work stability. The overall lifting guardrail device has good strength and greatly reduces the height of the entire machine during transportation. It is very convenient for loading and unloading, and can be assembled or disassembled in one lift.