BotulinumHydraulic lifting platformPurchase subsidy work

When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, electrical equipment or component failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.

An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, and the device will produce; Buzz&# quo; Noise.

Botulinum.Check valve leakage oil pipe check valve leakage. The solution is to carefully check whether the one-way valve is functioning properly. If it is not normal, it is recommended to replace the one-way valve with a new one.

Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.

.Regularly check the operation of each mechanism for normal operation and noise. If any faults are found, the hydraulic cargo elevator wholesale should be promptly eliminated. Otherwise, it will affect the use of the guide rail hydraulic lifting platform. When refueling, the hydraulic oil should be filtered and filled, and the refueling tools should be reliable and clean. The hydraulic cargo elevator manufacturer should not remove the filter at the fuel tank filler to improve the refueling speed. Refueling personnel should use clean gloves and work clothes to prevent solid and fiber impurities from falling into the oil.

After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.

Therefore, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.

Hydraulic cargo elevators have been used in some high-altitude operations in recent years, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes,BotulinumHydraulic mobile lifting platform, becoming a better choice for some high-altitude operations. However, there are still certain limitations, such as height and improving the quality of goods, which have certain constraints.

All high-altitude operations must first build scaffolding or take measures to prevent teams from falling before boarding the vehicle bridge.

Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.

There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load adjusting the center of gravity of the load, clean the problem it is necessary to park the car in a timely manner and replacing hydraulic oil wholesale for hydraulic cargo elevators.

When encountering signs of overheating in the electric motor, and continue running. The motor bearings should be smooth and outstanding.

Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

Affordable price.Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.

Due to the formation of a flow closed-loop, the volumetric speed regulation hydraulic elevator has good performance and high load stiffness. The hydraulic system using the volumetric speed regulation scheme has a higher efficiency and greater energy loss compared to the throttling scheme, the oil in the cylinder moves down the throttle valve under pressure, which will cause the temperature of the hydraulic system to rise. Not to mention anything else, just an intelligent alarm is enough to demonstrate the true value of hydraulic elevators.

Load bearing capacity: The lifting platform is placed on a horizontal support surface, and the workbench is evenly loaded to 125% of the maximum load capacity. After lifting 100 times, each load-bearing component must not have deformation or cracks.

Botulinum.Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.

The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged,BotulinumVehicle mounted hydraulic lifting platform, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.

Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.