Wieden Fixed h
Wieden MechaniThe electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
From this, it can be seen that the hydraulic lifting platform truck needs to carefully inspect the hydraulic and electrical systems before use so as to facilitate its use.
Wieden .Secondly, for the replacement of the hydraulic oil of the lifting platform truck, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, it must be turned on and automatically lifted 2 to 3 times to exhaust the air in the oil cylinder, maintain sufficient space, and ensure that the lifting platform truck can reach the rated lifting height.
When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, it is necessary to learn to analyze.
.When people choose mobile lifting platform vehicles, it is important to pay attention to their structural stability, as it directly affects whether the entire lifting platform can operate smoothly. If it has high strength and stable operation, it can support the design of the mechanism, and it is very scientific. Therefore, during use, it can ensure the overall structure is safe and stable, making people feel at ease.
The above detailed introduction, and these details cannot be ignored during the use process.
When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
In this situation, it is necessary to regularly check all wires and cables used to ensure that there is no damage. When there is wrapping or damage, the parts should be replaced in a timely manner. I believe many people have encountered overheating in electric motors. In this case, it is necessary to stop the motor in a timely manner, the motor shaft can be used and the effect is good.
Due to the fact that the power unit of hydraulic lifting platform vehicles requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric pole is very simple occupies small space, but does not have a price advantage. Therefore a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
When conducting a resistance check, it is necessary to disconnect the power supply. At this time, the circuit principle can be used to measure and then measure the magnitude of the resistance value
Information recommendation.The reason why many fields choose to use the electric elevator is that it can not only save manpower but also facilitate people's life in the process of use. The important thing is to solve the handling work, so that the electric elevator can be used to carry goods upstairs and downstairs. When transporting goods, the first thing everyone should pay attention to is its carrying capacity. Generally, around 500 kilograms of goods can be transported, so it is particularly convenient to use. It can be seen that the carrying capacity of electric elevators is relatively large.
Especially when its pipes are in use, they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms it is not allowed to carry people during use, and it is strictly prohibited to carry people. If the electric lifting platform truck carries people during use, the lifting platform is equipped with railings or anti crack valves, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
safety requirements .The characteristics of hydraulic lifting platform vehicles are very obvious, such as their overall weight being relatively light, and their maneuverability being relatively good, allowing even a single person to operate, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
After working for 10000 hours repair the mechanical and electrical systems of the elevator.
When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
Wieden .The advantages of fixed loading and unloading platform trucks: The application of fixed loading and unloading platform trucks is more energy-efficient than ordinary loading and unloading platform trucks, with automatic adjustment of lifting height to meet the transportation of goods, saving time for loading and unloading, and convenient operation. The entire loading and unloading process has high safety, and the design is more detailed than ordinary loading and unloading platform trucks, ensuring the quality of goods during smooth transportation.
The function of a fixed loading and unloading platform truck. The fixed loading and unloading platform truck meets the loading and unloading needs of goods, and has good load-bearing effect,Wieden Large hydraulic lifting platform, convenient loading and unloading, low consumption, and easy operation. The stability of the loading and unloading process is strong, and the height can be adjusted and lifted to a suitable position to meet the loading and unloading of goods. The later maintenance is in place and the maintenance cost is low.
When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time,Wieden 6-meter hydraulic lifting platform, the voltage value can be measured, in this case, it is necessary to learn to analyze.