LecceCylinder mounted hydraulic lifting platformPrice is bullish

In this situation, it is necessary to regularly check all wires and cables used to ensure that there is no damage. When there is wrapping or damage,LecceHydraulic guide rail lifting platform, the parts should be replaced in a timely manner. I believe many people have encountered overheating in electric motors. In this case, it is necessary to stop the motor in a timely manner, the motor shaft can be used and the effect is good.

When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.

Lecce.The lifting platform truck should be placed in a trench position and corresponding anti slip measures should be taken; Remove the gearbox of the equipment, remove the axle oil box, and take out the lower bearing and oil suction device; Slowly test drive and check if the surface around the axle diameter is severely damaged; If the damage is severe and tungsten is occupied, it should be polished smooth with an oilstone; Under the electric motor, place the sleeper on the trench edge on the inner side of the steel rail, use a jack to regularly pull the electric motor and remove the upper tile; How to solve the damage of important equipment in the lifting platform car? Check the status of the bearing pads and oil absorbers, investigate the cause of the damage, replace the bearing pads, and clean the bearing oil box; After assembling all components, install a new oil suction device on the axle oil box and clean the axle oil; Gear oil of gear box shall be as specified; Burning of axle box bearings is a common occurrence, which is the burning of outer bearings. In severe cases, it can cause the axle box and wheel set to be fixed together, affecting equipment operation.

When conducting a resistance check, it is necessary to disconnect the power supply. At this time, the circuit principle can be used to measure and then measure the magnitude of the resistance value

.Especially when its pipes are in use, they are quite boring and can roll, they need to be blocked or tied tightly. This is relatively appropriate, it is not allowed to carry people during use, and it is strictly prohibited to carry people. If the electric lifting platform truck carries people during use, the lifting platform is equipped with railings or anti crack valves, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.

When conducting a resistance check, it is necessary to disconnect the power supply. At this time, the circuit principle can be used to measure and then measure the magnitude of the resistance value

When conducting a resistance check, it is necessary to disconnect the power supply. At this time, the circuit principle can be used to measure and then measure the magnitude of the resistance value

When using a hydraulic lifting platform truck, there are many details that cannot be ignored. It mainly uses an external power supply, so when operating, the staff needs to master its operating knowledge, which is the basic content. At the same time, it is also necessary to master corresponding emergency response plans. When processing, it is also necessary to check the corresponding route, which is the basic content. So in addition, what preparations do hydraulic elevators need to master during use?

When using the elevator, the legs must be opened first. If the legs are not lifted, it is strictly prohibited to lift them.

To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.

Honest management.Nowadays, with electric elevators being a manifestation of technological progress. So what are the characteristics of electric elevators? Let's give you a detailed introduction below.

Of course, the hydraulic lifting platform truck uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform truck will be safer during operation. The process of operating the hydraulic lifting platform truck should be standardized,LecceHydraulic lifting table lifting, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.

The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.

High quality brand.When people choose mobile lifting platform vehicles, it is important to pay attention to their structural stability, it can support the design of the mechanism, and it is very scientific. Therefore during use, it can ensure the overall structure is safe and stable,LecceHousehold elevator, making people feel at ease.

Maintenance time regulations for hydraulic elevators: After 1500 hours of daily maintenance of the elevator, repair the mechanical and electrical systems.

When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.

Lecce.For lifting platform vehicles without manned protection it is strictly prohibited to carry people during use. At the same time, attention should be paid during use to prevent damage to hands, feet, and clothing.

The traction wheels of the mobile lifting platform vehicle can rotate at any angle during use making it convenient to operate in narrow spaces, making it particularly convenient to use. At present, the appearance of mobile lifting platform vehicles on the market looks very beautiful, and they are high-end, atmospheric and upscale, so the appearance looks very attractive and convenient to use, especially for lifting, so they can work at different heights. The important thing is that this elevating platform car can have electronic switches, point control, or continuous control, among other options.

When conducting a resistance check, it is necessary to disconnect the power supply. At this time, the circuit principle can be used to measure and then measure the magnitude of the resistance value