BazhouAutomati
BazhouHydrauliWorking at heights is a common practice nowadays, but it also has a certain degree of danger. So people invented hydraulic lifting platforms, which are more convenient to help people complete high-altitude operations. However, people should also pay attention when using hydraulic lifting platforms, otherwise they can easily malfunction, which may lead to serious consequences. So what are the common faults of hydraulic lifting platforms?
Drain and discard the hydraulic oil from the hydraulic lifting cargo elevator. For the outdoor guide rail elevator, tighten the joint and remove the oil filter. After cleaning, clean it with compressed air, and then return it to the oil tank and connect the pipeline.
Bazhou.The current should exceed the rated current, but also burn out. When a star connected motor is mistakenly connected into a triangle, or a motor with multiple coil groups connected in series into a branch is mistakenly connected into two parallel branches, it will cause the winding and iron core to overheat, and in severe cases, the winding will be burned out.
Regularly check all wires and cables for damage. Timely bandage and replace damaged parts. Various scissor lift manufacturers have formal qualifications. Welcome to inquire by phone and sincerely invite cooperation!
.Elevator customers all have overloaded use of elevators. Although elevators have a large overload capacity in design, the hidden dangers brought by such use are very large, which can easily cause damage such as oil cylinder roof fall and elevator bracket deformation. So it should be summarized as follows: Maintenance of elevators must be equipped with full-time elevator operators who have undergone on-the-job training, and illegal operation and use are strictly prohibited.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface,BazhouLifting hydraulic platform, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
Elevator customers all have overloaded use of elevators. Although elevators have a large overload capacity in design, the hidden dangers brought by such use are very large, which can easily cause damage such as oil cylinder roof fall and elevator bracket deformation. So it should be summarized as follows: Maintenance of elevators must be equipped with full-time elevator operators who have undergone on-the-job training and illegal operation and use are strictly prohibited.
The hook of the seat belt should not be hung on unstable or moving objects. High priced and various specifications of scissor lift manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!
The above introduction to common faults of hydraulic boarding bridges can be said to be very detailed. I hope everyone can respond well to various problems after reading it.
Check the rollers, intermediate shafts, and random adjustment can easily cause internal pressure to increase or decrease. In severe cases, it can shorten the service life of the motor.
No matter what problem occurs, if encountering an unsolvable problem with a hydraulic lifting platform,BazhouMobile hydraulic lifting table supply, it is better to produce it quickly and conveniently, and guide the manufacturer to solve it. Please pay attention to safety precautions during maintenance.
Good stability: The overflow valve can prevent excessive system pressure during upward movement. Emergency manual valve: In case of power failure, it can cause the elevator car to descend to the nearest floor position and open the door. Manual pump: When the system malfunctions, the manual pump can be operated to pump high-pressure oil to raise the car to the nearest floor position; Tank oil temperature protection: When the oil temperature in the tank exceeds the standard setting value, the oil temperature protection device sends a signal to suspend the use of the elevator. The elevator can only be started when the oil temperature drops.
When encountering overheating in the hydraulic elevator motor it is necessary to stop it in a timely manner, eliminate the fault, and continue running. The motor bearings should be in good condition.
Quality Assurance.What are the maintenance rules for the mechanical equipment of hydraulic elevators? The brakes of each mechanism should be regularly inspected and adjusted to ensure flexibility and reliability. On the friction surface, there should be no dirt present, and any dirt must be washed off with gasoline or thinner.
The above introduction to common faults of hydraulic boarding bridges can be said to be very detailed. I hope everyone can respond well to various problems after reading it.
When using the distribution box, the electric leakage switch meets the requirements for construction elevators. If the fixed elevator installed is variable frequency the selection of the leakage switch should be compatible with the frequency converter.
Bazhou.What are the pressures on lifting platforms? The movement of lifting platforms has always been a concern for us. Our usage scenarios are uncertain, and most of them are part-time workers. Therefore, in order to better attract customers, we are constantly researching mobile lifting platforms to meet different needs. However, we are still accustomed to using fixed elevators, He has a huge load capacity and strong stability, which can meet the needs of many customers, which is also the use of lifting platforms in China in recent years.
No matter what problem occurs, if encountering an unsolvable problem with a hydraulic lifting platform, it is better to produce it quickly and conveniently, and guide the manufacturer to solve it. Please pay attention to safety precautions during maintenance.
The application scenarios of mobile elevators may require several or even dozens of passenger elevators in some office buildings and hospitals. In order to increase the speed,BazhouHydraulic mobile lifting platform, efficiency, and usable area of electric elevators, most high-rise buildings will divide electric elevators into arrays, with each group responsible for a portion of the floors, and make different adjustments and scheduling based on the usage mode of different floors at different times.