HagueMicro electric hydraulic elevatorThere are coups to buy

Stage equipment safety door. To prevent personnel from extending their heads, hands, and feet out of the shaft and objects from falling into the vertical shaft. Its vertical position should be closed, its cabin should be full of doors, and the height of the hoistway (hall door) should not be less than 8 meters; The electric door opening and closing switches should be removed from the vertical and passenger compartment doors. In order to prevent accidents caused by vertical, and car roof doors not being closed.; Door interlocks should be installed on both the vertical and passenger compartment doors.

Protective measures should comply with regulatory requirements.

Hague.Folding arm electric elevators are mostly driven by hydraulic means, and the source of power for the hydraulic system is hydraulic oil. Only when the hydraulic oil quantity is sufficient and the oil quality is high, can the folding arm electric elevator provide greater torque output, thereby improving work efficiency. So, how can we determine whether the newly added hydraulic oil quantity is sufficient? What is the hydraulic oil quantity standard?

When the horizontal distance between the edge of the cage and the edge of the landing or between the cage and the landing door is greater than 150mm and there is no effective protection from other structures, the side protection device for the landing entrance should be equipped.

.Setting requirements: Drainage measures should be set up for the foundation of construction electric elevators to ensure smooth drainage.

The motor of the hydraulic guide rail lifting platform is set around the wellbore occupying a relatively small area, improving the utilization rate of the wellbore area.

The counterweight guide rail should meet the specification requirements.

In addition to ground protective fences, low level doors can be used. Low level doors should meet the following requirements: the height of the door should be between 1m and 2m. And there should be at least protective railings, a half height middle crossbar and a toe board at least 150mm above the ground.

High altitude operations and maintenance in areas such as repair,HagueElectric 6-meter elevator, logistics, electricity, transportation, chemical, hotel, sports center, mining, and enterprise. The lifting system of the lifting platform is driven by hydraulic pressure,HagueFully electric self-propelled elevator, also known as hydraulic lifting

The distance between the electric hoist and overhead line in Electrical safety construction shall meet the specification requirements, otherwise protective measures shall be taken.

Industry management.Low level doors should be equipped with interlocking devices that can verify their closed and locked positions. The action of this interlocking device should be at the entrance of the cage. Simple use should not interfere with the operation of the interlocking device. The attached wall bracket should use matching standard products. When the wall bracket cannot meet the requirements of the construction site, it should be designed separately. The design of the wall bracket should meet the requirements of component stiffness, strength, stability, etc., and the production should meet the design requirements.

Setting requirements: For construction electric elevators with foundations installed on roof slabs, or other lower suspended structures, the bearing capacity of the foundation support structure should be checked. Click here to download the construction technical information for free. Basic drainage facilities should be installed.

The wall bracket of the construction electric elevator should be intact and reliably fixed,HagueSecond floor electric elevator, and its attachment distance, wall bracket spacing, and end height must comply with the requirements of the 'User Manual'. The angle between the plane of the wall bracket and the normal direction of the attachment surface should not exceed 8 degrees;. When the attachment device does not meet the requirements of the 'User Manual' due to conditions, its calculation sheet, design, and production materials should be confirmed by the manufacturer or reviewed by the technical leader of the installation unit, and verified by experts.

Drainage measures need to be considered around the foundation. (Drain the accumulated water on the foundation).

quality standard.The quality of the standard section should comply with the product manual and specification requirements.

Normal operation starts. Click on this free download of construction technical information. Safety limit devices should be installed on electric elevators for construction with upper and lower limit switches that are sensitive and reliable.

When applying a normal force of 300N to any position on either side of the door using a rigid 5000mm2 square or circular flat surface in the locked position of the landing door, the door should be able to withstand and have no deformation; - Deformation not exceeding 30mm; After the test, it worked normally.

Hague.The landing door should meet the requirements of the specifications and achieve standardization.

Emergency manual valve: In case of power failure, it can cause the car to descend to the nearest floor position and open the door

Horizontal lead screw mechanical electricity