ArnhemHydrauli
ArnhemHydrauliSmall typesetting Copyright Shu ICP Bei No. 11019783-1
The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!
Arnhem.When a hydraulic lifting platform malfunctions, it is necessary to take time to prepare accordingly. At this time, it is necessary to provide timely feedback or communicate with the manufacturer. If a voltage range is used to detect the hydraulic lifting platform, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated.
.Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated.
Hydraulic lifting platform is a non scissor type hydraulic lifting platform and is also a widely used vertical transportation equipment for goods, among which the commonly used is the guide rail hydraulic lifting platform. Mainly driven by electric motors and oil pumps, heavy chains are driven by oil cylinders to drive the lifting and lowering of hydraulic lifting platforms. It is also widely used for vertical transportation of goods between high-rise buildings. So,ArnhemHydraulic lifting platform for loading, what are the advantages and characteristics of guide rail hydraulic lifting platforms?
The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged, and ensure that the lifting platform can be lifted to the rated lifting height.
When using a hydraulic lifting platform, there are many details that cannot be ignored. It mainly uses an external power supply, so when operating, personnel need to master its operating knowledge,ArnhemSmall hydraulic lifting platform, it is also necessary to master corresponding emergency response plans. When processing, it is also necessary to check the corresponding route, which is the basic content. So in addition, what preparations do hydraulic elevators need to master during use?
Regardless of the type of lifting platform used, people are more concerned about the stability during use. Because the stability not only affects the actual use effect, but also has varying degrees of impact on the safety during use, it is necessary to pay appropriate attention. The same applies when using fixed loading and unloading platforms, but many times the stability of this type of platform can be trusted. The reason for saying this is because the manufacturer has taken this issue into account during production and manufacturing, and the following aspects are taken to avoid this situation.
Installation conditions.Troubleshooting: When the elevator power light is turned on, press the up button, the motor rotates, but the lifting platform does not rise. This may be due to the reversal of the motor after the three-phase power supply is connected, just change the two phase wires of the heavy machine.
If hydraulic elevators are used on campus, it can better enhance the safety and security of the campus. For campuses, especially after school every day, there are a large number of parents and there are also safety hazards such as people and cars. Maintaining order in such situations is a good idea.
When using the elevator, we should listen for any abnormal noise. If there is any abnormal noise, we should immediately stop using it to avoid serious damage to the elevator.
The following is a brief description of the precautions for using high-altitude work platforms: high-altitude workers must hold a health certificate. Individuals with mental illness, hypertension or mental illness are not allowed to engage in high-altitude work tasks. Staff are not allowed to engage in high-altitude work while drinking alcohol or feeling mentally drained.
Installation conditions.Once again, whether the sealing rings are damaged or ineffective whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors,ArnhemSmall mobile hydraulic lifting platform, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.
When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
Original software
Arnhem.Tail signature:
Replace with
Small typesetting Copyright Shu ICP Bei No. 11019783-1