Las VegasElect
Las VegasProduthere should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)
The combined platform is often used in small workshops with small volume of goods. However
Protective device: In case of power or oil circuit failure, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.
Las Vegas.Clean the surface of the base and install anchor bolts. If the construction elevator is installed on the floor use a pad iron under the base screws to increase the force surface between the nut and the floor,Las VegasFixed electric hydraulic lifting platform, in order to reduce the impact of the nut on the floor; Insert steel plate gaskets of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite; After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and press it tightly
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment, leveling, and confirm that the foundation meets the requirements before construction.
The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.
After 10000 hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.
The hydraulic system of the fixed lifting platform of the hydraulic cargo elevator is equipped with anti fall and overload safety protection devices, and operation buttons can be set on each floor and the lifting platform workbench to achieve multi-point operation.
When the hydraulic oil is insufficient, the hydraulic pump will experience suction,Las VegasLarge hydraulic lifting platform, causing air to enter the hydraulic oil and producing high noise.
Quality improvement.When installing, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.
After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.
Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.
When using hydraulic elevators, frequent inspections and maintenance should be carried out, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).
Affordable price.Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.
Low power consumption: Hydraulic elevators are driven by the pressure generated by their own weight, with complete designated products and quality assurance
Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.
Las Vegas.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.
Wholesale manufacturers of hydraulic cargo elevators have found that the market demand for hydraulic cargo elevators is also increasing. More importantly, some cargo loading and unloading work, as well as decoration, hotels,Las VegasHydraulic aluminum alloy lifting platform, logistics, warehouses, supermarkets, etc., are commonly used in these situations, especially in the decoration industry. I have seen many decoration companies use small hydraulic cargo elevators, which are also specially processed and manufactured, and have some differences from the hydraulic cargo elevators we often see. There are significant differences in structure, shape, lifting speed, and height, and the prices of hydraulic cargo elevators also vary. The hydraulic cargo elevators used in the decoration industry have a low lifting height, some only 2 meters, and do not require many materials. He mainly promotes people, not goods, and rarely promotes goods, so the load is small, but not inferior to the use of other hydraulic cargo elevators. He is stable, safe, interpretable and durable enough to make hydraulic cargo elevators a good helper in the decoration industry. The function of hydraulic cargo elevators is gradually improving with our needs, and the properties we require are different. Wholesale manufacturers of hydraulic cargo elevators also manufacture according to our requirements.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.