ZhuozhouLarge 
ZhuozhouFixed An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed,ZhuozhouHydraulic lifting platform experiment, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.
Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.
Zhuozhou.There are two reasons for the sinking of the hydraulic cargo elevator table: on the one hand, the hydraulic pressure is flexible, and under high pressure or temperature, the volume will change, which is reflected in the lowering of the position on the table.
Voltage too low: Measure the starter voltage, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.
Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.
A hydraulic elevator is a type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
Users should arrange dedicated personnel to operate hydraulic elevators, formulate usage details and safety precautions for hydraulic elevators based on their own situation, and hang them on the
Cylinder diameter and hydraulic oil flow rate. The speed of the hydraulic lifting device is inversely proportional to the cross-sectional area of the cylinder rod and directly proportional to the flow rate of hydraulic oil. When the hydraulic elevator runs slowly, priority should be given to the hydraulic oil flow angle.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
Where is good.The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details check if the tools are complete, and ensure the smooth progress of the installation process.
Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for 1-2 people.
After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.
Quality risk.Pre install equipment maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation,ZhuozhouScissor fork hydraulic lifting platform, some require equipment such as forklifts for installation, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.
Oil cylinder leaks. Long term use causes wear on the sealing ring in the oil cylinder and excessive oil leakage in the cylinder wall gap,ZhuozhouElectric hydraulic fixed lifting platform, resulting in the natural descent of the hydraulic cargo elevator. The sealing components need to be replaced immediately.
When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.
Zhuozhou.Load bearing capacity: The lifting platform is placed on a horizontal support surface and the workbench is evenly loaded to 125% of the maximum load capacity. After lifting 100 times, each load-bearing component must not have deformation or cracks.
When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.