HaWarehouse boarding bridgeResearch on the tendency of failure

The use of imported seals ensures excellent sealing performance of the hydraulic system.

Chinese manufacturer of boarding bridges dedicated to mobile lifting (sh ē Ten series of hydraulic lifting platform products, including platform, self-propelled aerial work platform, fixed lifting platform, TTW guide type cargo lift, aluminum alloy (melting point 660 ℃) lifting platform, folding arm lifting platform, car mounted lifting platform, disabled lifting platform, lifting stage, boarding bridge, etc, All properties owned by the company

Ha.The problem of sealing ring damage is common in almost all hydraulic systems, insufficient compression of the sealing ring, etc. When the sealing ring is lifted and lowered for a long time, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, leading to gaps in the sealing performance of the sealing ring, resulting in oil leakage. At this time, only the damaged sealing ring needs to be found, Just replace it with a new one.

A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.

.The following is a brief introduction to the storage of hydraulic oil in fixed hydraulic boarding bridges for a wide range of users: when stopping the hydraulic oil drum and filling, it is necessary to achieve three passes and pass when receiving oil; Filtering during barrel rotation: When refueling the equipment, it is too cold to ensure the cleanliness of the bucket mouth, oil injection port, oil barrel,HaContainer truck boarding bridge, etc., to prevent impurities from entering the oil port and forming hydraulic oil purification.

The following is a brief introduction to the storage of hydraulic oil in fixed hydraulic boarding bridges for a wide range of users: when stopping the hydraulic oil drum and filling, it is necessary to achieve three passes and pass when receiving oil; Filtering during barrel rotation: When refueling the equipment it is too cold to ensure the cleanliness of the bucket mouth, oil injection port, etc., to prevent impurities from entering the oil port and forming hydraulic oil purification.

It mainly includes the strong wind load acting on the structure, the lateral force caused by the inclined operation of the fixed hydraulic boarding bridge when lifting the channel, the horizontal load on the structure caused by suspended objects under wind load, the fixed hydraulic boarding bridge, as well as temperature load, technical load, and ice and snow load. The special load of fixed hydraulic boarding bridge refers to the large load that may be encountered by the lifting equipment during non operational conditions, or the occasional unfavorable load encountered during operational conditions. This load is encountered in both hydraulic lifting channels and fixed hydraulic climbing bridge lifting channels.

There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.

　　2. Platform side boarding bridge: The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages.

The following is a brief introduction to the storage of hydraulic oil in fixed hydraulic boarding bridges for a wide range of users: when stopping the hydraulic oil drum and filling, it is necessary to achieve three passes and pass when receiving oil; Filtering during barrel rotation: When refueling the equipment, it is too cold to ensure the cleanliness of the bucket mouth, oil injection port, oil barrel, etc., to prevent impurities from entering the oil port and forming hydraulic oil purification.

Focus on Development.Function: Convenient unloading, strong stability and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platforms, lifting platforms, and unloading platforms: anti slip device: This device is welded from steel plates, which can effectively achieve anti slip function and is safe and reliable.

The use of imported seals ensures excellent sealing performance of the hydraulic system.

Main technical indicators: Large dynamic load: 6T Large static load: 6T Large width: 2M Large length: 4M Electric hydraulic imported from France assembled mobile hydraulic boarding bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is a cargo auxiliary equipment used in conjunction with forklifts. With the help of this equipment forklifts can directly enter the interior of the car compartment for batch loading and unloading operations. Only one person is required to operate without the need for power supply, but also double the efficiency of loading and unloading operations which can achieve safe and fast loading and unloading of goods. It can not only reduce your labor intensity, speed up the flow of materials, and obtain greater economic benefits.

Product features: Fully hydraulic drive, easy to operate and reliable to operate.

Honesty is the foundation.Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.

Its design is usually fully standardized as early as the structural design of buildings.

Main technical indicators: Large dynamic load: 6T Large static load: 6T Large width: 2M Large length: 4M Electric hydraulic imported from France assembled mobile hydraulic boarding bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is a cargo auxiliary equipment used in conjunction with forklifts. With the help of this equipment, which can achieve safe and fast loading and unloading of goods. It can not only reduce your labor intensity, but also double the efficiency of loading and unloading operations,HaMobile hydraulic boarding bridge,Ha10 ton fixed boarding bridge, speed up the flow of materials, and obtain greater economic benefits.

Ha.There are generally several forms of axle 1. Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device. Its design is usually fully standardized as early as the structural design of buildings.

Install anti rolling foot skirts on both sides to prevent accidental injury to the toe platform.

The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability.