PesackManual p
Pesack3-meter In this situation, it is necessary to regularly check all wires and cables used to ensure that there is no damage. When there is wrapping or damage, the parts should be replaced in a timely manner. I believe many people have encountered overheating in electric motors. In this case, it is necessary to stop the motor in a timely manner,PesackSelf propelled hydraulic lifting platform, and then troubleshoot the problem before continuing to use it. This way, the motor shaft can be used and the effect is good.
When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
Pesack.The manual hydraulic scissor platform vehicle has the following characteristics: suitable for long-distance transportation; Treadable feet and protective devices; Lightweight and easy to lift; Unique caster design ensures safety; The engineering handle design ensures comfortable operation for the operator.
From this, it can be seen that the hydraulic lifting platform truck needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.
.When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
The design of hydraulic lifting platform vehicles should consider actual needs, and attention should be paid to these related platform vehicles when using them. When designing, many details of the lifting platform vehicles are crucial, as they can display products and understand prices.
Of course, the hydraulic lifting platform truck uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform truck will be safer during operation. The process of operating the hydraulic lifting platform truck should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
The quality of the body is defective, and it is recommended that the manufacturer replace it. The probability of this situation occurring is relatively low.
When conducting a resistance check, it is necessary to disconnect the power supply. At this time, the circuit principle can be used to measure and then measure the magnitude of the resistance value
Quality assurance.When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
When using, mainly in the center of the countertop. However, for special cases, partial loading is allowed, so this detail needs to be noted during use.
The characteristics of hydraulic lifting platform vehicles are very obvious such as their overall weight being relatively light, and their maneuverability being relatively good, allowing even a single person to operate, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations it can only briefly overload by 10%.
Standard requirements.There are many details that need to be paid attention to when using an electric lifting platform car, such as placing it on a flat surface during use to prevent tipping during work. In addition, what are the precautions for using electric lifting platform vehicles?
When using the elevator, we should listen for any abnormal noise. If there is any abnormal noise, we should immediately stop using it to avoid serious damage to the elevator.
The characteristics of hydraulic lifting platform vehicles are very obvious, such as their overall weight being relatively light, and their maneuverability being relatively good, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course some small and narrow channels are also possible, it is necessary to disconnect the power supply. At this time so we need to pay attention to this point.
Pesack.When conducting a resistance check,PesackGuide rail hydraulic lifting platform, the circuit principle can be used to measure and then measure the magnitude of the resistance value
The above detailed introduction, I believe everyone has a comprehensive understanding and understanding of the use of hydraulic elevators, and these details cannot be ignored during the use process.
I believe many people are familiar with mobile elevating platform vehicles. In daily life, we often see that this elevating platform vehicle is used in many fields, but we need to pay attention to details during the use process.