Schigerzent mi
Schigerzent mibuildings
Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, airports, stations, sports venues, workshops, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.
Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, under the action of high pressure the hydraulic system inevitably causes the hydraulic valve to flow back or the sealing components to produce oil. The main reasons for the natural descent of the hydraulic cargo elevator include the following points: replacement of the support valve due to leakage. The lowering valve is damaged or not powered on. Require the lowering valve to be kept clean on a daily basis, and if damaged, replace it with a new hydraulic lowering valve in a timely manner.
Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.
.When using hydraulic elevators, frequent inspections and maintenance should be carried out, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking
Pay attention to checking each steel wire rope for signs of broken wires and loose drums. If it exceeds the relevant rules, it is necessary to replace it immediately. The protection of steel wire ropes should strictly follow the rules of GB5144-85.
Hydraulic cargo elevators have been used in some high-altitude operations in recent years,Schigerzent michlosMast type aluminum alloy hydraulic lifting platform, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes, becoming a better choice for some high-altitude operations. However, there are still certain limitations, such as height and improving the quality of goods, which have certain constraints.
Therefore, the oil should be replaced regularly to ensure that the additives are effective. The filter can only absorb a limited amount of dirt particles and other impurities from the oil. Replace the filter according to the recommended cycle to keep the system clean.
The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning,Schigerzent michlosHydraulic fixed lifting platform, clean the filter and add new oil after using a new filter element.
Information recommendation.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.
Pay attention to checking each steel wire rope for signs of broken wires and loose drums. If it exceeds the relevant rules, it is necessary to replace it immediately. The protection of steel wire ropes should strictly follow the rules of GB5144-85.
Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.
Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract,Schigerzent michlosScissor type hydraulic lifting platform, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.
target.Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.
The manufacturer of hydraulic cargo elevators tells you the precautions for high-altitude operations.
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking
Schigerzent michlos.Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.
When using hydraulic elevators frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).