VenedalBoardinWhen working on the hydraulic boarding bridge the support legs must be extended, and the support leg bolts must be adjusted to ensure that the lifting platform is stably stressed on the support legs and kept horizontal; During the lifting process and in the lifting state, the lifting platform must not be moved, it should be stopped immediately for inspection to avoid causing serious damage to the lifting platform; Before use, check whether the electrical equipment is normal; All shaft pin oil holes must be oiled before each use. Before use, it is necessary to perform no-load lifting and check whether the hydraulic system is normal; The load of the workbench should not exceed the rated value, and it should not be subjected to intense manual shaking; The hydraulic oil in the oil tank must be replaced every 500 hours of operation.
The correct operation of the hydraulic boarding bridge is good maintenance, and how to operate it correctly. Let me briefly introduce the operating steps of the hydraulic boarding bridge hoping to bring more help to everyone.
Venedal.On a moving steel structure slope, the air conditioning panel will automatically rise. Release the button, adjust the plate to reduce itself, and the hinge is used on the truck.
conduct.
Tighten the manual valve to close it.
Monthly maintenance of hydraulic boarding bridges: check for wear on rollers, intermediate shafts and bearings, cylinder pins and bearings, boom hinge shafts and bearings etc; The oil quality and level of hydraulic oil; The hydraulic boarding bridge should be raised throughout the entire process, the hydraulic surface should be 40 to 50 millimeters higher than the bottom of the box. The hydraulic oil is darkened and at this position, sticky, or has foreign objects such as gravel. If found, it should be replaced in a timely manner; Add some oil to each part to extend the service life of the bearing. The hydraulic boarding bridge has a wide range of uses. Doing the above points well not only ensures your personal safety but also extends the service life of the equipment, making the boarding bridge better serve you.
The outstanding characteristics of air suspension are good smoothness,VenedalMovable boarding bridge, less maintenance, long service life, significant improvement in protection of cargo compared to steel plate suspension, and greatly reduced damage to the entire vehicle and road surface. The leaf spring produces different bending under different loads, so the distance between the whole vehicle and the ground is always changing. If the load is increased while keeping the spring unchanged, it will also reduce the natural frequency of the spring and even change the characteristics of the spring. The air spring is based on the compressibility of air. The air enclosed in the air bag is an element. Different air bag pressures of the air spring system balance different loads. When the height of the air bag is fixed, the distance between the car body and the road surface remains unchanged.
The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and take corresponding drainage measures for the top, surface, and foot of the slope, especially for the simple boarding bridge.
Open the manual valve, slowly lower the boarding bridge,VenedalMobile Yard Ramps , and secure more than 90% of the lip plates at the bottom of the container.
After the boarding bridge work is completed,VenedalManufacturing of boarding bridges, all parts should be scrubbed and cleaned. When not working, the workbench should be lowered to a low position.
When it comes to fixed hydraulic boarding bridges, I believe
market.Check if the manual valve is open. When using, it must be opened, otherwise the boarding bridge may be damaged.
Usage environment: Able to adapt to specific working environments, such as working in highly corrosive, high-temperature, and low-temperature environments.
The reason for the natural descent of the hydraulic boarding bridge lifting platform is that the one-way valve is leaking, the lowering valve is not tightly sealed, and the oil cylinder is leaking. Solution: Check the one-way valve in the valve group. If dirt is found on the sealing surface of a single valve, clean the one-way valve. Check if the lowering valve has power. If there is power, troubleshoot the lowering valve itself or replace the lowering valve. The slide valve of the lowering valve must be kept clean and move flexibly.
Venedal.When working on the hydraulic boarding bridge, the support legs must be extended, and the support leg bolts must be adjusted to ensure that the lifting platform is stably stressed on the support legs and kept horizontal; During the lifting process and in the lifting state, the lifting platform must not be moved, and it is strictly prohibited to shake on the lifting platform. If there is an abnormal sound during the operation of the hydraulic boarding bridge, it should be stopped immediately for inspection to avoid causing serious damage to the lifting platform; Before use, check whether the electrical equipment is normal; All shaft pin oil holes must be oiled before each use. Before use, it is necessary to perform no-load lifting and check whether the hydraulic system is normal; The load of the workbench should not exceed the rated value, and it should not be subjected to intense manual shaking; The hydraulic oil in the oil tank must be replaced every 500 hours of operation.
1. Before use, check the boarding bridge for obvious damage such as cracks and broken wires.
The width of the boarding bridge also requires a certain width of its own. However, if the width is too small, it is not conducive to forklift loading and unloading of goods. If the width is too large, it can occupy a certain space, which is not necessary. So a reasonable width is necessary, usually the width of the electric hydraulic boarding bridge is 1800mm, 2000mm, and 2100mm. The width of the bridge is divided into internal width and total width. As we have already mentioned, the internal width is the width of the passage, and the total width mainly refers to the width of the guardrails on both sides plus the width of the passage. The total width can be ignored in use, but everyone still cares about the internal width, which is the width of the channel.