XinminMobile h
XinminAutomati
XinminHydrauliWhen the motor overheats, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.
Leading spaces in blank lines Full width: Font size: Replace: Replace
Xinmin.When using, the weight should be evenly distributed, mainly in the center of the countertop. However, for special cases, partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load, so this detail needs to be noted during use.
Pay attention to checking each part of the steel wire rope for broken wires and loose strands. If the tide passes through the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
.Later, when there is a major malfunction of the lifting platform, it should be repaired by professional personnel as soon as possible. After the malfunction occurs, it should not be used again to avoid accidents, personnel and property losses.
Due to the fact that the power unit of the hydraulic lifting platform requires an oil source its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
Convert to Simplified Chinese Convert to Traditional Chinese without converting the number of blank lines between paragraphs before and after:
Using Help
The electric lifting platform needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
Update Log
demand.The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site,XinminSmall hydraulic platform lift truck, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!
Shafts must have split pins and be sufficient.
Pay attention to checking each part of the steel wire rope for broken wires and loose strands. If the tide passes through the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
Sincere service.For customers to use and operate the lifting platform for a long time, the editor briefly introduces how to maintain and repair the lifting platform: First of all, normal maintenance is mainly focused on prevention, especially if any damage or malfunction is detected and corrected or repaired in a timely manner. Careful inspection and maintenance at this time can save costs and avoid larger problems, resulting in costly repairs.
When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case there may be short lines or damaged components. Using a table for inspection is relatively better.
Special manufacturing processes. Everyone knows that fixed loading and unloading platforms can have a good market performance, which is closely related to the advanced manufacturing technology of manufacturers. In fact, it can still improve the quality and production efficiency of manufacturers' products to a certain extent. As for this type of loading and unloading platform, manufacturers use many special manufacturing processes during production, which makes it highly stable in application.
Xinmin.Shafts must have split pins and be sufficient.
Replace with
The reduction gearbox, gearbox,XinminHydraulic unloading platform,XinminHydraulic lifting platform factory, external gear teeth, are all carried out according to the requirements in the table.