repair310s stainless steel plateTensile strength analysis

Four in one formula and process conditions Preparation of solution Take formula 1 as an example: mix the calculated amount of water for zinc oxide into a paste, slowly add it into the calculated amount of phosphoric acid under stirring until it is completely dissolved, then add zinc nitrate and tartaric acid, dilute it with water to 2/3 of the total volume, add sodium alkosulfonate and OP emulsion, and stir to make it completely dissolved. Then add chromium dihydrogen phosphate dissolved in dilute phosphoric acid, and add titanium sulfate. After all materials are added, dilute them to the total volume, stir them to make the solution even cool them to room temperature, put a large amount of iron filings in the solution, and soak them for 2-3 days to make them contain enough ferrous ions. When the content of ferrous ion reaches above 7g/L, adjust the free acidity and total acidity of the solution to the specified value, and then the solution can be used at elevated temperature. When the ferrous ion reaches the above value, the phosphating speed is fast, the solution is stable, attention shall be paid to controlling the temperature. If the temperature is higher than 70 ℃, the degreasing technology of degreased copper pipe. How to make degreased copper pipe? The process flow of degreased copper tube? What are the characteristics of degreased copper tubes? Use of degreased copper tube? There are too many questions. Let's solve them at once. Everyone knows the copper tube. Nitrate reacts easily. The heater should be installed on the two walls of the tank, not on the bottom of the tank, to prevent local overheating. Stainless steel pipe or iron pipe should be used for heater, and lead pipe or copper pipe should not be used to avoid contamination of solution by impurities. What is degreased copper pipe? &The advantages of degreased copper pipe's comprehensive treatment of grease, rust removal, phosphating and passivation are described. This comprehensive treatment process can simplify the process, reduce the work area, save equipment costs, shorten working hours, improve labor productivity and reduce costs. This method can only be used in the occasions where the requirements for coating quality are not high.However, in actual production, due to the amount of oil contamination, light and heavy rust, the consumption rate of each component in the solution is different, so attention should be paid to adjustment and control to maintain its due role. What is the degreasing copper tube? &I have roughly known the degreasing methods of degreasing copper tubes: solvent degreasing, alkali degreasing, ultrasonic degreasing, high pressure hot water degreasing, electrolytic degreasing, etc. 1 Solvent degreasing: use degreasing solvent to dissolve the oil on the surface of red copper pipe, collect it together into a container, volatilize, collect and reuse the volatile solvent, and separate the pollutants from the circulation system. This method was used in the early stage, which has problems such as low cleaning efficiency, difficult maintenance, and environmental pollution. In recent years, many kinds of surfactants have been developed.

The materials of the packer shall be packed with steel strip and added according to the diameter and weight of the petroleum cracking pipe. The degreased copper pipe from the pipe can be packed without a packer. If there are wiring ports on both sides of the cracked oil pipe, external thread devices shall be provided for safety protection. Brush the nozzle with clean oil or anti rust oil. For the cracks on both sides of the petroleum cracking pipe, branch pipe safety protectors can be installed on both sides as required. If the oil cracking pipe is installed in the container, the container shall be lined with waterproof devices, such as woven cloth and straw mats. In order to better distribute the textile petroleum cracking tubes in the tank, the packer can weld the safety protection support frame inside the petroleum cracking tubes. Previous page: How to clean plastic coated copper tubes. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. When plastic coated copper pipe is cut, the wound is uneven and cracked. Then I will introduce how to solve these problems. For the disconnection part of plastic coated copper pipe, the position and direction shall be drawn with tape or other measuring tools and the disconnection line shall be marked in combination with the construction drawing and site conditions. When the petroleum cracking pipe is disconnected, please fix the equipment with square steel pipes such as vises, and cut it after fixing. In the area to be disconnected, use a towel or soft cloth to crack the oil stain or dirt on the surface of the pipe. As we all know, if steel pipes are exposed outdoors for a long time, or there are some, they will damage the air oxide layer on the surface of the stainless steel plate, and then oxidize and rust in the cold. Gas. Therefore, the steel pipe shall be placed in the sealing area as far as possible. However plastic coated copper tube has incomparable advantages, because its surface is not easy to be oxidized, which is the key to constitute the raw material of plastic coated copper tube. The high-precision plastic coated copper pipe has an extremely thin, firm and smooth chromium rich air oxide film on its surface to prevent oxygen molecules from re penetrating and re oxidizing in the air, thus preventing rust. The description of the plastic coated copper pipe shows that the part with weak corrosion resistance of the transition film will produce pitting corrosion reaction due to the self-excited reaction, and the small holes will form highly corrosive aqueous solution. The chloride ion content will accelerate the corrosion rate.

repair.Copper tape: 600 * 1500 1000 * 2000 Complete specifications: thickness 0.2-3mm, C1100, C1220, copper content: 99% with excellent thermal conductivity,repair2205 stainless steel plate, excellent cold and hot processing performance, welding and brazing, and good corrosion resistance.

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, it has more advantages in strength. Medical copper tubes have many different s in practical application, medical copper tubes have the same tensile strength, torsional strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, such as oil drilling equipment, rotating shafts bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials simplify the production process, save raw materials and manufacturing hours, such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, communication, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil, copper and aluminum pipes - and the old ones, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank, so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the sling should be relaxed, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

.The price can be changed, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, which was in disorder; Before ten o'clock, it was not as expected, and users were very cautious in purchasing; Around 11:00, the surrounding markets became loose and the price was low. High hanging, low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much and the market transaction is weak - this week's trading days, the spot price rose, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, and the shipment was not much. Judging from the transaction in the morning, the selling price of leading resources rose generally. Among the resources in Kuti, the base price of t2 copper tube was 5050 yuan/ton, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, under the pressure of futures, the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions, few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, and the purchasing enthusiasm is not high. According to traders' feedback the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.

The process flow of plastic coated copper pipe: the settlement price of 904l stainless steel plate is on the high side, and the price is stable. 904l stainless steel plate: last Friday, the steel plant made all the orders. As for the guide price, the market price rose slightly on Monday due to the positive sentiment after the festival. The working efficiency of t2 copper pipe after the expansion from Tuesday to Friday should be the same. Between the upper and lower clamping groove bodies of the alloy pipe to be flared, the end of the alloy pipe to be flared faces the flaring die, extends a certain length (depending on the flaring length), and then drives the upper clamping groove body to move down through the oil cylinder. Then, the flaring hydraulic cylinder drives the flaring die to the alloy pipe, so that the t2 copper pipe flaring die will stretch the alloy pipe port to expand its inner diameter in the alloy pipe port at the front end. The length of flared section can be 20200 mm. How to solve the crack of plastic coated copper pipe? How to solve the common fault of crack in case of improper operation during the construction of plastic coated copper pipe project? If it is not handled in time, there is a serious risk. Therefore, I will carry out practical operations in strict accordance with the engineering construction specifications and requirements related to immediacy, find more practical welding processes and then ensure the welding quality of electric welding. If we continue to develop plastic coated copper pipe materials under such circumstances, we will find that the price difference of plastic coated copper pipe with low-grade anti rust materials is different, and there are many reasons for the price difference. First, there are significant differences in production. Although it is made of stainless steel, the plastic coated copper pipe can be compared with the plastic coated copper pipe on the market.

Manufacture gear, worm gear and other high-strength wear-resistant parts and high corrosion resistance elastic components. Key points of semi continuous casting process for copper tube: The copper tube has strong air absorption, easy oxidation and slag formation, large solidification shrinkage poor thermal conductivity and other casting properties, and poor casting performance; Before casting, some alkaline earth metal compounds, such as Na3A lF6 and NaF mixture, which is effective for improving the purity of liquid metals and the crystal structure of ingots. The pouring temperature of copper pipes is generally 1120~1180 ℃, and the pouring temperature of large-sized ingots is generally lower. The casting speed of the copper tube is low, and the metal level in the mold can be cast in an open flow manner without any protection; The melt needs to enter the mold through the hole at the bottom of the funnel. The design of funnel aperture should meet two conditions at the same time: one is to ensure the flow matching the casting speed; Second, the joint coating must be carefully carried out to avoid concentrated shrinkage cavities in the ingot. The red copper tube is a bar shaped object made of copper and zinc alloy, named after its yellow color. Copper content is 56%~68% brass, and its melting point is 934967 degrees. Brass has good mechanical properties and wear resistance, and can be used to manufacture precision instruments, ship parts, gun casings, etc. Different zinc content also has different colors. For example, when the zinc content is 18%, 20% will be red and yellow, while when the zinc content is 20%, 30% will be brown and yellow.

When cutting the copper pipe of air conditioner, use tools such as clamps to fix the copper bar and then cut it, rather than fixing it by hand, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, the global mining industry will rise again, and the W-shaped trend will fully emerge. In the second half of the year, the factors affecting the European market of tinned copper bars have gradually weakened, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, and the possibility of a crisis in the next period of time is also reduced. In recent years, the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, and the market price has rebounded to around 7600 dollars per ton. Driven by this, products including aluminum, zinc and other products have also rebounded. Only nickel, a basic metal product, has remained weak.

Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.

However, for some important parts, it is also considered that the yield ratio should be smaller to improve their safety and reliability. However, at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, gas and steam; Boiler pipes and steam transmission pipes are used for the piping, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation, automobile, tractor and other industrial sectors; Pipe for petroleum industry, mainly used for oil and gas exploitation, such as casing, drill pipe and tubing, and pipe for petroleum refining and processing; Pipe for mechanical manufacturing, which is used to manufacture the race of ball bearing, the plunger, rotating shaft and body of air pump and hydraulic pump; High pressure vessel, used for manufacturing bottles, boilers, shells, etc. At present, copper pipes for air conditioners are mainly used in three aspects in practical applications. First, medical copper pipes are widely used in industrial plants, high-rise civil buildings, municipal engineering, oil platforms,repairQ345D alloy round steel, bridges, railway vehicles and other fields. Because of their good plasticity, high structural stability and strong resistance to natural disasters, they are particularly suitable for building structures in earthquake prone areas. Second the air conditioning copper pipe has high tensile strength and toughness, high buildings,repairAluminum plate, bridges and other steel structures have good cold bending performance and welding performance, and the section size and surface quality are well controlled, so it is widely used in vehicle manufacturing, large bridge construction, mechanical manufacturing, industrial plant components and many other industries. Third, microwave transfer station towers, construction crane towers, elevator supports, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials, especially not for the reaming and fat wall perforation. When using a general piercer, the wall thickness/pitch diameter ratio (T/D limit is about 6%, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

original.The utility model relates to a connecting structure, in particular to a connecting structure of a copper tube and an aluminum row. At present, most of the copper aluminum transition joints have not been effectively protected. In this way, under the condition of long-time electrification and heating and affected by the water vapor or corrosive gas in the air, the parts at the connection point are more likely to be oxidized, resulting in the reduction of the effective contact area of the connection point, the increase of the contact resistance, and the excessive heating or even burning of the connection point.

The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, agricultural and chemical machinery, glass curtain walls, boiler construction, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing weldability and corrosion resistance.

The copper tube warehouse of automobile air conditioner shall not be stacked with acid, alkali, salt, cement and other materials that are corrosive to steel. The air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of the air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel.

Four in one formula and process conditions Preparation of solution Take formula 1 as an example: mix the calculated amount of water for zinc oxide into a paste, slowly add it into the calculated amount of phosphoric acid under stirring until it is completely dissolved, then add zinc nitrate and tartaric acid, dilute it with water to 2/3 of the total volume, add sodium alkosulfonate and OP emulsion, and stir to make it completely dissolved. Then add chromium dihydrogen phosphate dissolved in dilute phosphoric acid, and add titanium sulfate. After all materials are added, dilute them to the total volume, stir them to make the solution even, cool them to room temperature put a large amount of iron filings in the solution, and soak them for 2-3 days to make them contain enough ferrous ions. When the content of ferrous ion reaches above 7g/L, adjust the free acidity and total acidity of the solution to the specified value, and then the solution can be used at elevated temperature. When the ferrous ion reaches the above value, the solution is stable, attention shall be paid to controlling the temperature. If the temperature is higher than 70 ℃ the degreasing technology of degreased copper pipe. How to make degreased copper pipe? The process flow of degreased copper tube? What are the characteristics of degreased copper tubes? Use of degreased copper tube? There are too many questions. Let's solve them at once. Everyone knows the copper tube. Nitrate reacts easily. The heater should be installed on the two walls of the tank, not on the bottom of the tank, to prevent local overheating. Stainless steel pipe or iron pipe should be used for heater, and lead pipe or copper pipe should not be used to avoid contamination of solution by impurities. What is degreased copper pipe? &The advantages of degreased copper pipe's comprehensive treatment of grease, rust removal, phosphating and passivation are described. This comprehensive treatment process can simplify the process, reduce the work area, save equipment costs, shorten working hours, improve labor productivity and reduce costs. This method can only be used in the occasions where the requirements for coating quality are not high.However in actual production, due to the amount of oil contamination, light and heavy rust the consumption rate of each component in the solution is different, so attention should be paid to adjustment and control to maintain its due role. What is the degreasing copper tube? &I have roughly known the degreasing methods of degreasing copper tubes: solvent degreasing, alkali degreasing, ultrasonic degreasing, high pressure hot water degreasing, electrolytic degreasing, etc. 1 Solvent degreasing: use degreasing solvent to dissolve the oil on the surface of red copper pipe, collect it together into a container, volatilize, collect and reuse the volatile solvent, and separate the pollutants from the circulation system. This method was used in the early stage, which has problems such as low cleaning efficiency, difficult maintenance, and environmental pollution. In recent years, many kinds of surfactants have been developed.

The cost is reasonable.The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, it has more advantages in strength. Medical copper tubes have many different s in practical application, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, such as oil drilling equipment, rotating shafts, bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials simplify the production process, save raw materials and manufacturing hours, such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, communication, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank, so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

Dissolved oxygen in water is a major factor in copper pipe corrosion.

However, for some important parts, it is also considered that the yield ratio should be smaller to improve their safety and reliability. However, at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, gas and steam; Boiler pipes and steam transmission pipes are used for the piping, structure and steam transmission of steam boilers, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation, automobile, tractor and other industrial sectors; Pipe for petroleum industry, such as casing, drill pipe and tubing, and pipe for petroleum refining and processing; Pipe for mechanical manufacturing, which is used to manufacture the race of ball bearing, the plunger, used for manufacturing bottles, boilers, shells, etc. At present, medical copper pipes are widely used in industrial plants, high-rise civil buildings, municipal engineering, oil platforms, bridges, railway vehicles and other fields. Because of their good plasticity, the air conditioning copper pipe has high tensile strength and toughness they are particularly suitable for building structures in earthquake prone areas. Second, high buildings, bridges and other steel structures have good cold bending performance and welding performance, and the section size and surface quality are well controlled, large bridge construction, industrial plant components and many other industries. Third, air conditioning copper pipes are mainly used to make transmission line towers, microwave transfer station towers, construction crane towers, elevator supports, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials, especially not for the reaming and fat wall perforation. When using a general piercer the wall thickness/pitch diameter ratio (T/D limit is about 6%, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

repair.The material cost of medical copper tube will not be less than 40 yuan. The better the material is, the higher the price will be. It is called &one cent, one cent&. Moreover in addition to the production and operation costs, labor costs, factory rent, etc. you must pay attention to the quotation below 45 yuan/square. Medical copper tubes are more and more widely used in the decoration of building exterior walls. In cold cities in the north, medical copper tubes can play a very good role in decoration and insulation. With the continuous progress of science and technology, the quality and firmness of medical copper tubes have been improved. However as long as the decoration materials are used, they will inevitably crack during installation and construction. As time goes by, there will be aging to varying degrees in daily life. Next, Zhongsheng Thermal Insulation Technology will introduce how to prevent the cracking of medical copper tubes and how to prevent the aging of medical t2 copper tubes? Let's talk about these two issues. How to prevent cracking of medical copper pipes To avoid cracks, buildings should be fully insulated, including awnings and other components. Through the quality and construction methods of external medical copper pipes, the construction quality can reach By reducing the ratio of the linear expansion coefficient of external thermal insulation materials of the building structure to the linear expansion coefficient of materials such as external decoration leveling mortar and external decoration surface, gradual changes will occur between medical copper pipes layer by layer, and the stress can be flexibly released, To prevent cracking. How to prevent medical copper tube from aging? The insulation layer of high-rise buildings shall have fire resistance , and shall have the characteristics of preventing fire spread and releasing smoke or toxic gas in case of fire. The strength and volume of materials shall not be reduced too much, and the surface shall not burst or collapse. Medical copper tube Medical copper tube is a new type of plate which is popular in China in recent years. It has many advantages, fire insulation, sound insulation, convenient construction, beautiful appearance, etc., and is deeply welcomed by the industry. The medical copper pipe may fall during use. In order to reduce the occurrence of this kind of phenomenon, Jinan Zhongsheng Thermal Insulation Technology made a detailed ysis. Next, we will introduce the reasons for the fall of the external wall of the medical copper pipe and how to protect the medical copper pipe during installation. Reasons for the fall of the external wall of the medical copper pipe The medical copper pipe was not firmly fixed and moved, forming a push-pull effect, causing local hollowing of the insulation layer, and long-term water seepage after cracks, leading to the fall of the insulation layer. 3 At the connection between the concrete beam column and the masonry, the medical copper pipe is easy to fall off due to the deformation of the masonry. 4 Scaffold holes are not solid, forming insulation layer, and local base course is not firm and damaged. 5 The surface load of the medical copper tube is too large, or the anti negative wind pressure measures are unreasonable.

Pay attention to the following points when using flame heating brazing: the selection of welding materials The filler metal is wire or rod, with a diameter of about 35mm. The material is: the melting temperature of wire 221 is about 0905 ℃. Its chemical composition is FB10 The composition is 2331% H3BO3 and 6071% KBF The joint form of brazed copper pipe is mostly plug-in. Before cleaning the brazed copper pipe before welding, the edge of the pipe mouth must be corrected and deburred to ensure that the pipe mouth is free of cracks or other defects. And clean the surface of the inserted part. After the red copper pipe is assembled by tack welding, it shall be fixed by tack welding. The number, size and height of tack welds shall be symmetrically and evenly distributed along the circumference from top to bottom, left to right, and the tack welds shall be melted into the whole weld during brazing. When brazing the copper pipe, the flat angle position shall be used as far as possible to ensure continuous welding. Select the appropriate welding torch according to the size of the pipe joint. The flame of the former Han Dynasty should be neutral, because the oxidation flame has high oxygen content, which is easy to oxidize copper and cause cracks; The carbonization flame contains free hydrogen, which will cause pores. When heating pipes before welding, the flame shall be perpendicular to the heating surface, the pipe joints shall be heated evenly, and the base metal shall be heated as quickly as possible to avoid excessive temperature and heating time of the through pipe joints. During the brazing of degreased copper tube, the brazing seam and filler metal shall be under the protection of flame. In addition, it shall be noted that the brazing seam shall be naturally cooled after welding, and the weldment shall not be moved before the brazing seam has solidified. After natural cooling after welding, hot water or wet cloth shall be used to wipe the brazing seam and remove welding slag to improve corrosion resistance and reliability of post welding inspection.

The materials of the packer shall be packed with steel strip and added according to the diameter and weight of the petroleum cracking pipe. The degreased copper pipe from the pipe can be packed without a packer. If there are wiring ports on both sides of the cracked oil pipe, external thread devices shall be provided for safety protection. Brush the nozzle with clean oil or anti rust oil. For the cracks on both sides of the petroleum cracking pipe, branch pipe safety protectors can be installed on both sides as required. If the oil cracking pipe is installed in the container, such as woven cloth and straw mats. In order to better distribute the textile petroleum cracking tubes in the tank the packer can weld the safety protection support frame inside the petroleum cracking tubes. Previous page: How to clean plastic coated copper tubes. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. When plastic coated copper pipe is cut, the wound is uneven and cracked. Then I will introduce how to solve these problems. For the disconnection part of plastic coated copper pipe, the position and direction shall be drawn with tape or other measuring tools and the disconnection line shall be marked in combination with the construction drawing and site conditions. When the petroleum cracking pipe is disconnected, please fix the equipment with square steel pipes such as vises, and cut it after fixing. In the area to be disconnected use a towel or soft cloth to crack the oil stain or dirt on the surface of the pipe. As we all know, if steel pipes are exposed outdoors for a long time, or there are some, and then oxidize and rust in the cold. Gas. Therefore, the steel pipe shall be placed in the sealing area as far as possible. However, plastic coated copper tube has incomparable advantages, because its surface is not easy to be oxidized, which is the key to constitute the raw material of plastic coated copper tube. The high-precision plastic coated copper pipe has an extremely thin, firm and smooth chromium rich air oxide film on its surface to prevent oxygen molecules from re penetrating and re oxidizing in the air, thus preventing rust. The description of the plastic coated copper pipe shows that the part with weak corrosion resistance of the transition film will produce pitting corrosion reaction due to the self-excited reaction, and the small holes will form highly corrosive aqueous solution. The chloride ion content will accelerate the corrosion rate.