Phuentsholing Copper plateSelection of standard parts

When cutting the copper pipe of air conditioner, use tools such as clamps to fix the copper bar and then cut it, rather than fixing it by hand, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place, and then processed again after cooling, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, the global mining industry will rise again, and the W-shaped trend will fully emerge. In the second half of the year, there were signs of stabilizing and rebounding. In terms of the macro factors affecting the bulk commodities the factors affecting the European market of tinned copper bars have gradually weakened, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, and the possibility of a crisis in the next period of time is also reduced. In recent years, the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, and the market price has rebounded to around 7600 dollars per ton. Driven by this, products including aluminum, zinc and other products have also rebounded. Only nickel, a basic metal product, has remained weak.

The price can be changed, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, which was in disorder; Before ten o'clock, it was not as expected, and users were very cautious in purchasing; Around 11:00, the surrounding markets became loose and the price was low. High hanging, low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, the spot price rose and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, and the shipment was not much. Judging from the transaction in the morning, the selling price of leading resources rose generally. Among the resources in Kuti, the base price of t2 copper tube was 5050 yuan/ton, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, under the pressure of futures, the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, and the purchasing enthusiasm is not high. According to traders' feedback, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.

Phuentsholing .On November 11, the market price of Cangzhou copper bar was stable. According to the monitoring data of Lange Iron and Steel's cloud business platform, the market price of 57 * 5mm cold drawn steel produced in Linyi is 4850 yuan, the market price of 108 * 5mm in Linyi is 4450 yuan, the market price of 219 * 6mm in Jianlong is 4650 yuan the market price of 219 * 6mm in Yuanhua is 4600 yuan, the market price of 325 * 10mm in Juneng is 4800 yuan, and the market price of 530 * 10mm in Juneng thermal expansion is 5100 yuan.

The demand for t2 copper tubes is increasing. At the same time, in the market, the quality identification method of t2 copper tube for grid fittings is currently accompanied by rapid economic development. There are many kinds of sales, different purposes, and different quality. Therefore, when purchasing, you should be clear and have certain selection skills. Here we introduce the quality identification method of t2 copper tube. The color of t2 copper tube depends on the color of t2 copper tube. Although the external color is a visible factor, the color of the product is closely related to its production process and quality control. If the product is bright in color and high in glossiness, it is generally superior to the product with poor color. The t2 copper tube with uniform thickness should be selected. Because some small manufacturers are limited in technology and process it is difficult to ensure that the product thickness is uniform and neat. Therefore, the thickness is also an important factor to test the quality of the pattern plate. Later, the casting process of t2 copper tube.

.No heating and plating bath is required. The process is simple and easy to operate. The cold drawn degreased copper tube bright tin plating is one of the anti discoloration mirror bright brush tin plating and degreased copper tube tin plating mean copper bar partial or overall tin plating.

One of the classification of copper tubes. The common wave shape is a single copper tube. Hyperbolic means that two different arcs overlap on the same surface, that is, starting from different circle centers, draw arcs in two radii. The red copper tube is a module made of double curves designed according to the drawings. The red copper tube is light in weight, good in rigidity and high in strength. The shapes of the red copper tubes processed are different and can be processed into various geometric shapes such as arcs and spheres. It is beautiful, elegant and colorful. Let's talk about the two main methods of processing and forming the copper tube: The hot processing and forming method is to roll the copper tube to a roughly hyperbolic shape, then heat it, then slowly beat it with a hammer, finally cut, weld, fold polish and polish it. The whole process needs to be very careful to ensure the surface quality of the copper tube. This forming method is very suitable for parts with small model and large arc change. When the model size is relatively large and complex, it can be considered to break it into small pieces for forming, the cost is high and the production period is long. 2 Forming method of roll bending This method is to make some modifications on the roll bending machine, and change one of the shafts into a concave type and the other into a convex type. This method can form a regular copper tube like a sphere, with a small processing range, but it has great advantages for copper tubes with small radians. What problems should be paid attention to when designing the hyperboloid copper tube? Everyone knows that the design of the air conditioning copper tube is very important. To achieve the beautiful shape, exquisite workmanship and fashionable personality of the hyperboloid copper tube, first of all, the design is very critical. Some small copper tube companies are not mature enough in design and have not enough design experience, so they often have problems in design, Hyperbolic copper tube is very famous for preparing some details that we should pay attention to in the design. The sculpted copper tube is highly decorative, and the production and processing technology of hyperbolic shaped copper tube is relatively complex. Copper tube products with strong aesthetics. According to the design requirements, different shapes need to be molded for the sculpted copper tube, so the production process of sculpted aluminum veneer is relatively complex.

Plastic coated copper pipe is one of the safe carbon fiber products. Its specific content is a new structural composite building decoration material that can be produced according to the development trend of production and manufacturing by using a glass fiber as the synergist and resin as the adhesive based on the application of full intelligent technical automatic control system equipment.

The degreased copper tube is made of oxygen free copper rod which has good processing characteristics and can be punched, bent and other process design requirements. The surface can be subject to anti-corrosion treatment, such as nickel plating, tin plating, etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin, and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe so as long as it is used correctly, there is no need to worry about safety. When choosing to decorate the house, few people ask about the water supply pipe of the house. In fact, the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and more than 99% of the water will disappear after entering the degreased copper tube for 5 hours. This biological characteristic is that there is a small amount of copper ions dissolved in water in the degreased copper tube, and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer, which can resist extreme weather and is suitable for the long-term surface of metal materials. The actual effect of salt and water corrosion resistance is good. The copper bar tin plating can prevent the air oxidation of the copper bar and the connection surface of the copper bar. In addition, the melting of metal tin and copper will produce aluminum alloy, which will improve the adhesion of copper strip coating. In addition, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times, which greatly increases the service life of the copper and plays a considerable role in protecting the copper. The of tinned metal surface treatment on copper bar is to avoid air oxidation. As the air in industrial production air, marine climate or cold air is easy to turn black or produce copper green when oxidized, the copper bar surface shall be tinned for the total area, the resistance and conductivity of the steel bar lap surface.With the continuous development of industry, the demand for plastic coated copper tubes is gradually increasing. Then how to apply wood grain paint on alloy pipes. Wood like paint is a kind of wood like paint. It is used for spraying plastic coated copper pipe and its process flow. Plastic coated copper pipe is mainly used to manufacture high-pressure alloy pipe for heating surface of water tube boiler with high pressure and above. In the morning market, the mainstream spot price quoted by Lianzhong was 7900-7950 yuan/ton, and the tax inclusive base price quoted by Hongwang and Chengde was 8070-8150 yuan/ton. On a month on month basis, and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP, UHP and subcritical power plant boilers. Third,Phuentsholing 304 stainless steel plate, large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

Continuous casting and rolling method: This production method is to directly cast hollow copper billets after electrolytic copper smelting and use planetary rolling method to produce copper tubes.

Attention shall be paid to the purchase of red copper pipe in order to study the distribution law of pipeline crack stress field under internal pressure. The simulation ysis and experimental verification are carried out for pipes with cracks of different shapes, different directions, different internal pressures and different sizes. The results show that the stress at the crack tip is much greater than that at the crack center. The crack shape has little effect on the stress. With the increase of the included angle between the crack direction and the pipe axis, the stress at the crack tip first increases and then decreases. With the increase of the pipe internal pressure, crack depth, and crack length, the stress at the crack tip increases linearly. Among them, the effect of crack length on the stress at the crack tip is smaller than that of internal pressure and crack depth. During the construction and operation of long-distance pipeline, due to the influence of pipe manufacturing defects welding defects, internal and external loads, stress concentration, the pipeline will produce cracks and expand cracks, which is the most dangerous defect of long-distance pipeline and the main reason for pipeline failure. At present, pipeline cracks are mainly determined by internal testing and non-destructive testing after excavation. Among them, ultrasonic internal testing has a good identification rate for cracks with a length of more than 25 mm, a depth of more than 1 mm in the base metal or a depth of more than 2 mm in the weld; Magnetic flux leakage internal detection has a certain detection rate for cracks with opening more than 0.25mm, but it is difficult to identify and quantify. In NDT, magnetic particle, eddy current and radiographic methods have high detection and identification rate. The generation and propagation of cracks will cause local stress concentration in the pipeline, which is prone to brittle fracture, fatigue damage, corrosion damage and other failure phenomena, seriously affecting the service performance and reliability of long-distance pipeline. In this paper, the influence of crack shape, direction and size on the stress at the crack tip is yzed by studying the stress field distribution law of copper pipe cracks, which provides a reference for the prevention and control of pipe cracks. What problems will be encountered in the production of copper tubes. The production of copper pipe includes four steps: welding,Phuentsholing Stainless steel coiled plate, forming, inspection and pipe expansion.

Marketing Department.Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding, chromium oxide heat return color will appear on both sides lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, the chromium content on the metal surface will, and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand, glass beads or other abrasives previously used on ordinary carbon steel low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, the wire ropes, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, retained retained austenite can achieve a certain buffer effect. After cold treatment, the air conditioning copper pipes need to be taken out and put into hot water for heating, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less, the internal surface layer of the copper tube is larger,Phuentsholing Copper plate, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets, and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, and its market potential is huge. Problems such as incomplete penetration, deformation, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, the structure and properties of the base metal are almost unchanged, so that the original service properties of the base metal can be maintained.

No heating and plating bath is required. The process is simple and easy to operate. The cold drawn degreased copper tube bright tin plating is one of the anti discoloration mirror bright brush tin plating and degreased copper tube tin plating mean copper bar partial or overall tin plating.

The demand for t2 copper tubes is increasing. At the same time, in the market the quality identification method of t2 copper tube for grid fittings is currently accompanied by rapid economic development. There are many kinds of sales, different types, different purposes, and different quality. Therefore, when purchasing, you should be clear and have certain selection skills. Here we introduce the quality identification method of t2 copper tube. The color of t2 copper tube depends on the color of t2 copper tube. Although the external color is a visible factor, the color of the product is closely related to its production process and quality control. If the product is bright in color and high in glossiness, the casting process of t2 copper tube.

The price can be changed the thickness is also an important factor to test the quality of the pattern plate. Later it is difficult to ensure that the product thickness is uniform and neat. Therefore, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, which was in disorder; Before ten o'clock, it was not as expected, and users were very cautious in purchasing; Around 11:00, the surrounding markets became loose and the price was low. High hanging, low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, and the shipment was not much. Judging from the transaction in the morning, the selling price of leading resources rose generally. Among the resources in Kuti, the base price of t2 copper tube was 5050 yuan/ton, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, under the pressure of futures, the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions, few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, and the purchasing enthusiasm is not high. According to traders' feedback, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.

Focus on Development.The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support steel structure engineering, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction, highway railings, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

Advantages of red copper tube Durability: copper has stable chemical properties, integrating cold resistance, heat resistance, pressure resistance, corrosion resistance and fire resistance, and can be used in different environments for a long time.

Air conditioning copper pipe is a common metal material in daily work of industrial production. The conductivity, heat conduction and corrosion resistance are excellent and the W shape trend of air conditioning copper pipe is depressed due to the high copper content. Good machinability, fusion welding and brazing are very good. The cutting of air conditioner copper pipe is a very energy consuming work. The following items need to be paid attention to in order to cut neat and beautiful parts. Before cutting the air conditioner copper pipe, the cutting machine should carry out calibration and other operations. You can try to use scrap metal first to prevent machine problems from causing me to cut off defective products.

Phuentsholing .In future work, try to protect the surface of the copper tube.

When cutting the copper pipe of air conditioner, use tools such as clamps to fix the copper bar and then cut it, rather than fixing it by hand, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place, and then processed again after cooling, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, the global mining industry will rise again, and the W-shaped trend will fully emerge. In the second half of the year, there were signs of stabilizing and rebounding. In terms of the macro factors affecting the bulk commodities, the factors affecting the European market of tinned copper bars have gradually weakened, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, and the possibility of a crisis in the next period of time is also reduced. In recent years, the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, and the market price has rebounded to around 7600 dollars per ton. Driven by this, products including aluminum, zinc and other products have also rebounded. Only nickel, a basic metal product, has remained weak.

The price can be changed, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, it was not as expected, and users were very cautious in purchasing; Around 11:00, the surrounding markets became loose and the price was low. High hanging low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, the spot price rose, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, the selling price of leading resources rose generally. Among the resources in Kuti, the base price of t2 copper tube was 5050 yuan/ton and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, under the pressure of futures, the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, and the purchasing enthusiasm is not high. According to traders' feedback, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.