LexlipGuide ra
LexlipHydrauliand daily cleaning work should be carried out. Dust and debris on the motor should be cleaned in a timely manner.
In the construction elevator, the switch box also has leakage protection equipment, and its wires and cables have good insulation without leakage. The metal passing through the wires is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, without any issues of strand breakage or shrinkage, and of course, the number of broken wires should not exceed the corresponding standards. His pulley movement is very flexible.
Lexlip.Readjust the overflow valve when the pressure is low. Adjust the oil level to be too low at 100% rated load, fill the hydraulic oil with suction oil, filter the blockage,LexlipHydraulic straight top lifting platform, and clean the oil suction section of the filter for air leakage. Check the oil suction pipe and joints; Tighten the joint. Replace the connector if necessary.
Precautions for daily maintenance of hydraulic elevator: Check all hydraulic pipelines and joints of the hydraulic elevator. The pipelines must not be damaged, and the joints must not be loose. All joints must be tightened.
.When encountering overheating in the electric motor during daily maintenance of the elevator,LexlipHydraulic lifting platform supplier, it is necessary to quickly park the car, remove obstacles, and then continue running. The motor bearings should be smooth and excellent.
In the construction elevator, the switch box also has leakage protection equipment, and its wires and cables have good insulation without leakage. The metal passing through the wires is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and of course, the number of broken wires should not exceed the corresponding standards. His pulley movement is very flexible.
Replace with new oil and do not intermittently use old oil, otherwise the moving parts in the system will accelerate wear.
Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.
Whether it is a large machinery with complex structure or a small to medium-sized equipment with simple structure, adjustment, fastening, and corrosion prevention, commonly referred to as" Cross homework”.
When encountering overheating in the electric motor during daily maintenance of the elevator, it is necessary to quickly park the car, remove obstacles, and then continue running. The motor bearings should be smooth and excellent.
management.The daily maintenance of guide rail type lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, eliminate faults and achieve these benefits for improving work efficiency, extending equipment service life, and ensuring the safety performance of the elevator.
The contact opening and closing of the travel switch of each safety device must be reliable, and the contact crater should be polished in a timely manner.
It is strictly prohibited to connect the motor of the lifting platform to the wrong power supply. It should be ensured that the voltage is 380V or 220V, and daily cleaning work should be carried out. Dust and debris on the motor should be cleaned in a timely manner.
Maintain a smooth access road for external construction elevators and sufficient parking space for equipment. When using a crane for auxiliary installation full consideration should be given to whether the on-site environment meets the operating conditions of the crane.
How many?.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, occupying an area of only 3-4 square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit and the top layer can be installed at a height of more than 5 meters. The computer room can be located within a radius of 15 meters of the shaft, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.
This series of products has a load capacity of 0.1 to 0.8 tons,LexlipFoot hydraulic lifting platform vehicle, and can also be customized according to user requirements, with a load capacity of up to 10 tons.
How to maintain elevators in winter is one reason and the primary reason. Many workers in other industries do not know that hydraulic elevators use different types of hydraulic oil in summer and winter. Often, at low temperatures, the hydraulic oil used in summer can become, or even freeze. After entering low temperatures in winter, it is important to remember to replace hydraulic oil containing antifreeze, which is suitable for working at low temperatures.
Lexlip.Preparation before folding and installation of the elevator. Carefully prepare a special construction plan for installation and provide safety technical disclosure to the installation personnel.
Every month, it should be ensured to add butter twice to the transmission position where the grease nipple is located. For areas where butter cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.
Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%