RotlingenTwo t
RotlingenType Before installing the elevator bearings, which can lead to premature bearing damage. Additionally,RotlingenLogistics hydraulic lifting platform, ensure that the installation environment is clean and do not bring iron filings, dust, and other objects into the bearings. Even small dust particles can cause premature bearing damage, Prolonged use can also affect the running in between bearings, leading to a decrease in the lifespan of the elevator.
After entering winter, elevators are prone to some small problems and malfunctions, which requires users to perform seasonal maintenance and upkeep on the elevator. Below the editor will briefly introduce the winter maintenance precautions and key points of the elevator.
Rotlingen.When the lowering valve is open and the lowering button is released, use a voltmeter to check whether the lowering valve is energized. If there is no power, check the circuit and eliminate the fault; If there is electricity, eliminate the malfunction of the lowering valve itself. The slide valve of the lowering valve must be kept clean and move flexibly.
Loosening: The motor fan makes a sound when it rotates. If the screws that fix the motor are loose, coupled with its own vibration, the motor collides with other components, resulting in a sound; The joints of each pin shaft are dry lacking oil, and there is hard friction between the iron parts, which not only damages the components but also produces abnormal noises. Therefore, the editor should emphasize again that timely maintenance and frequent refueling are important; If the hydraulic lifting platform does not rise, there is air in the hydraulic oil. You can open the exhaust hole, add gas, and then tighten it again; Hydraulic oil solidification: replace the hydraulic oil; Oil leakage: Check if there is any oil leakage at the interfaces of each oil pipe. If there is any oil leakage, replace it in a timely manner; Motor reversal: Check for wiring errors; (Manufacturers of hydraulic lifting platforms who do not understand electricity in a timely manner)
.Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.
Elevator customers all have overloaded use of elevators. Although elevators have a large overload capacity in design, the hidden dangers brought by such use are very large, which can easily cause damage such as oil cylinder roof fall and elevator bracket deformation. So it should be summarized as follows: Maintenance of elevators must be equipped with full-time elevator operators who have undergone on-the-job training, and illegal operation and use are strictly prohibited.
The lifting platform has been inspected and debugged before leaving the factory, and all technical indicators meet the design requirements. When in use, only the power supply needs to be connected and the hydraulic and electrical systems basically do not need to be adjusted.
The daily maintenance of guide rail type lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, eliminate faults, and achieve these benefits for improving work efficiency, extending equipment service life, replace the valve with a new one. Professional manufacturer of scissor lift lifts for quality assurance. The promotional activity is ongoing, and new and old customers are welcome to come for consultation
The boxes and distribution boxes of hydraulic elevators should be kept clean regularly, and dust on electrical equipment should be promptly cleaned.
Packaging strategy.Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%
The sinking of a cargo elevator is a phenomenon where the table surface drops due to gravity after a certain period of time when it rises to a designated position. Of course, the editor summarizes the ultimate solution.
The contact opening and closing of the travel switch of each safety device must be reliable and the contact crater should be polished in a timely manner.
What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than 5 meters. The computer room can be located within a radius of 15 meters of the shaft, occupying an area of only 3-4 square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.
Inspection environment.According to Beijing regulations, there will be electric brushes,RotlingenHydraulic lifting platform, and the parts between the brushes must be kept clean. Regular inspections are also required between the various bearings inside the machine, especially when adding butter to the bearings. If the butter is insufficient, it will cause severe wear and tear during the operation of the bearings, affecting the service life of the machine. There are various wires and cables inside the machine, and after a period of use, it is necessary to inspect the wires and cables. If any damage is found to the wires and cables,RotlingenElectric hydraulic lifting platform, it is necessary to repair or replace them. Regularly check whether the screws at this connection are loose. If any screws are found to be loose, they should be tightened. Some screws must meet certain torque requirements. In the absence of relevant professional equipment, you can use professional equipment to tighten the screws at the repair shop. It is necessary to ensure that the screws meet the corresponding torque requirements.
Maintain a smooth access road for external construction elevators and sufficient parking space for equipment. When using a crane for auxiliary installation, full consideration should be given to whether the on-site environment meets the operating conditions of the crane.
Rotlingen.Replace with new oil and do not intermittently use old oil, otherwise the moving parts in the system will accelerate wear.
Regularly check all wires and cables for damage. Timely bandage and replace damaged parts. Various scissor lift manufacturers have formal qualifications. Welcome to inquire by phone and sincerely invite cooperation!
Before installing the elevator bearings, do not open the packaging too early. This can easily lead to premature bearing contamination, which can lead to premature bearing damage. Additionally, ensure that the installation environment is clean and do not bring iron filings, dust, and other objects into the bearings. Even small dust particles can cause premature bearing damage, Prolonged use can also affect the running in between bearings, leading to a decrease in the lifespan of the elevator.