EnsadHydraulic
EnsadMobile hyEach box, distribution box, etc. is usually kept clean, and dust on electrical equipment should be quickly swept away.
Are there any damages to the wires and cables of the department. We need to quickly bandage and replace the damaged department.
Ensad.The axle manufacturer's oil cylinder is leaking and the oil cylinder seal is being replaced. The lifting platform does not lower and the lowering valve is malfunctioning. When the lowering button is pressed, check if the lowering valve is energized. If there is no electricity, try to eliminate it; If there is electricity, troubleshoot the lowering valve itself or replace the lowering valve. The lowering valve should be kept clean.
High altitude work is now also very common, and elevators are also highly demanded by the market. Many high-rise transportation tasks are completed by elevators, with high efficiency and reassuring safety. However, attention should also be paid to the installation of the elevator, otherwise there may be problems,EnsadPlatform hydraulic lifting, the elevator should be placed on a solid and flat ground to prevent tipping during operation. Press&quo; Rising; Or&quo; Descending; Press the button to frequently check and maintain the various components of the elevator when lifting the workbench. If the workbench does not move and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.
During use, it should be immediately stopped for inspection. When the working pressure of the electric elevator is found to be too high or the sound is abnormal it should be immediately shut down for inspection to avoid serious mechanical damage; Regularly check the working status of the shaft pin every month. If any loose shaft pin or screw is found, it must be locked tightly to prevent accidents caused by the shaft pin falling off.
The daily maintenance of guide rail type cargo elevators should ensure that the transmission position where the grease nipple is located needs to be lubricated twice a month. For areas where grease cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, container, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting requirements of different operation heights, and can be equipped with various table forms (such as ball, roller, turntable, steering, tipping, telescoping), and with various ways (separate, linkage,EnsadProduction hydraulic lifting platform, prevention), it has the characteristics of stable and accurate lifting, frequent starting, and large load capacity Effectively solve various lifting and lowering difficulties in industrial enterprises, making production operations easy.
The daily maintenance of guide rail type lifting equipment should pay attention to regular inspection and maintenance eliminate hidden dangers, and achieve these benefits for improving work efficiency,EnsadSmall hydraulic lifting platform, extending equipment service life, and ensuring the safety performance of the elevator.
How much does it cost?.Talking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.
Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.
Elevator customers all have overloaded use of elevators. Although elevators have a large overload capacity in design, the hidden dangers brought by such use are very large, which can easily cause damage such as oil cylinder roof fall and elevator bracket deformation. So it should be summarized as follows: Maintenance of elevators must be equipped with full-time elevator operators who have undergone on-the-job training, and illegal operation and use are strictly prohibited.
The inconsistent production dimensions of the hydraulic lifting platform support rods are a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace them, as the probability of this situation occurring is relatively low.
High value.The sinking of a cargo elevator is a phenomenon where the table surface drops due to gravity after a certain period of time when it rises to a designated position. Of course, this problem is definitely abnormal. So how can we solve it? The first step is to identify the cause. Below, the editor summarizes the ultimate solution.
Purpose The hydraulic lift is widely used in various industrial enterprises and production lines such as automobile, container mold manufacturing, wood processing, chemical filling, etc., to meet the lifting requirements of different operation heights, and can be equipped with various table forms (such as ball, roller, turntable, tipping, telescoping), and with various ways (separate, linkage, prevention), it has the characteristics of stable and accurate lifting, frequent starting, and large load capacity, Effectively solve various lifting and lowering difficulties in industrial enterprises, making production operations easy.
What are the maintenance rules for the mechanical equipment of hydraulic elevators? The brakes of each mechanism should be regularly inspected and adjusted to ensure flexibility and reliability. On the friction surface, there should be no dirt present, and any dirt must be washed off with gasoline or thinner.
Ensad.When using, the four legs should be firmly supported on a solid ground (based on the walking wheel about to leave the ground), and sleepers can be used when necessary.
The contact opening and closing of the travel switch of each safety device must be reliable, and the contact crater should be polished in a timely manner.
Familiarity with the usage process and without a doubt, this is the first thing to understand. There are two ways to understand it: first, carefully read the user manual provided by the manufacturer when the hydraulic lifting platform leaves the factory; The second is the equipment that needs to be installed. A professional installation technician will be dispatched to install the hydraulic lifting platform. After the installation is completed, relevant users will be trained on the operating process and safety precautions of the hydraulic lifting platform, and some maintenance matters in the future will also be explained; What should be paid attention to during the running-in period when using hydraulic lifting platforms? Check the wear of components. For newly processed and assembled components, there may be subtle deviations in shape and size that require a period of time for running-in. Therefore, it is necessary to pay attention to whether there is any rapid wear. If there is any, the manufacturer of the hydraulic lifting platform should handle it in a timely manner to avoid equipment failure; Work between the pins and bearings to ensure that they are not worn, and add some engine oil or grease appropriately; Confirm if there is any noise during the running-in period. If it is found that the hydraulic lifting platform is noisy during operation, there is no need to worry in the early stage. If there are no major problems, run it several times more. After the running-in, the noise will naturally disappear. However, if there is noise for a long time and no signs of fading, check if there are any signs of looseness in screws, nuts, retaining rings, oil pipe joints, etc. If there are any, please reinforce or replace them in a timely manner to avoid accidents.