ShandongHydrau
ShandongLarge Construction elevators are commonly used in industrial or construction sites in our daily lives, mainly for transporting people and goods. We can effectively use construction elevators to improve the efficiency of operations and greatly reduce the workload of operators. So, aged or damaged; The solution is to replace the gear pump.
Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.
.Each box, distribution box, etc. is usually kept clean, and dust on electrical equipment should be quickly swept away.
How to maintain elevators in winter is one reason and the primary reason. Many workers in other industries do not know that hydraulic elevators use different types of hydraulic oil in summer and winter. Often, the hydraulic oil used in summer can become, or even freeze. After entering low temperatures in winter, it is important to remember to replace hydraulic oil containing antifreeze, which is suitable for working at low temperatures.
Before installing the elevator bearings, do not open the packaging too early. This can easily lead to premature bearing contamination, which can lead to premature bearing damage. Additionally, ensure that the installation environment is clean and do not bring iron filings,ShandongSmall hydraulic lifting and leveling, dust, and other objects into the bearings. Even small dust particles can cause premature bearing damage Prolonged use can also affect the running in between bearings,ShandongLifting platform hydraulic pressure, leading to a decrease in the lifespan of the elevator.
What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than 5 meters. The computer room can be located within a radius of 15 meters of the shaft, occupying an area of only 3-4 square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.
What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and elevator are intact, input shaft, and elevator groove of the motor.
Every month, it should be ensured to add butter twice to the transmission position where the grease nipple is located. For areas where butter cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.
Highly recommended.When encountering overheating in the electric motor during daily maintenance of the elevator, it is necessary to quickly park the car, and then continue running. The motor bearings should be smooth and excellent.
Drain and discard the hydraulic oil from the hydraulic lifting cargo elevator. For the outdoor guide rail elevator, tighten the joint and remove the oil filter. After cleaning, clean it with compressed air, and then return it to the oil tank and connect the pipeline.
Replace with new oil and do not intermittently use old oil otherwise the moving parts in the system will accelerate wear.
What are the common faults of hydraulic lifting platforms? The hydraulic lifting platform's oil cylinder is severely damaged, and uneven damage to the inner sealing ring or obstacles inside can easily cause uneven stress, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.
Executive standard.Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.
When using the hydraulic lifting platform, it is also necessary to check for overheating, as this equipment is equipped with a motor. If the motor is overheated, it may cause damage to the motor. However, replacing a motor is relatively expensive. Therefore, during driving or trial operation, if the motor is found to be overheated, it should be stopped immediately, and then the fault that caused the motor to overheat should be checked and eliminated, Only then can the machine continue to be used.
Installing bearings for elevators may seem simple, but it is also important to pay attention to some details such as: it is actually difficult to thrust bearings into the shaft pins when excessively installing them. However, sometimes, some people may think of using a hammer to hammer the bearings for convenience,ShandongHydraulic lifting platform experiment, and use brute force during installation. In fact, directly hitting the bearings with a hammer can cause significant damage to the bearings, which is the main reason for bearing damage and reducing the service life of the bearings. So when installing bearings, we must not go too far. Fortunately, we can place some soft cloth or cardboard on top of them before installing them.
Shandong.No matter what problem occurs, if encountering an unsolvable problem with a hydraulic lifting platform, it is better to produce it quickly and conveniently, and guide the manufacturer to solve it. Please pay attention to safety precautions during maintenance.
The hook of the seat belt should not be hung on unstable or moving objects. High priced and various specifications of scissor lift manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!
Talking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.