HagueHandmade 
HagueTwo ton h
HagueCylinder Avoid, especially during storage. Store in a cool and dry place, and avoid rainy and snowy weather during work.
Loosening: The motor fan makes a sound when it rotates. If the screws that fix the motor are loose, coupled with its own vibration, the motor collides with other components, resulting in a sound; The joints of each pin shaft are dry, lacking oil, and there is hard friction between the iron parts, which not only damages the components but also produces abnormal noises. Therefore the editor should emphasize again that timely maintenance and frequent refueling are important; If the hydraulic lifting platform does not rise,HagueHydraulic lifting table lifting, add gas there is air in the hydraulic oil. You can open the exhaust hole, and then tighten it again; Hydraulic oil solidification: replace the hydraulic oil; Oil leakage: Check if there is any oil leakage at the interfaces of each oil pipe. If there is any oil leakage, replace it in a timely manner; Motor reversal: Check for wiring errors; (Manufacturers of hydraulic lifting platforms who do not understand electricity in a timely manner)
Hague.System: Anti type electronic control system, remote control system, PIC system.
After entering winter, elevators are prone to some small problems and malfunctions, which requires users to perform seasonal maintenance and upkeep on the elevator. Below, the editor will briefly introduce the winter maintenance precautions and key points of the elevator.
.Precautions for daily maintenance of hydraulic elevator: Check all hydraulic pipelines and joints of the hydraulic elevator. The pipelines must not be damaged, and the joints must not be loose. All joints must be tightened.
The correct construction inspection of the airport is to first inspect the foundation to see if there is any water accumulation and to see if the grounding system meets the requirements. We also need to see how the structural bolts of this frame are tightened and whether there are any cracks in the welds. We need to set them according to the instructions. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, there are also many safety equipment for elevators.
The pressure of the lifting platform is very important. When lifting goods, the pressure of the lifting platform will test the weight of the goods. If it is overloaded, the general lifting platform will prompt, which serves as protection. Therefore, now lifting platforms are equipped with pressure gauges. Hydraulic machinery should remind everyone to pay attention to the following points: the precautions for using small lifting platforms are based on pressure. Their load-bearing capacity is very poor and their size is small. When using the lifting platform, it is necessary to pay attention to its use. If overloaded, it will cause structural damage to the lifting platform. We have mentioned this many times before when using it.
Working at heights is a common practice nowadays, but it also has a certain degree of danger. So people invented hydraulic lifting platforms, which are more convenient to help people complete high-altitude operations. However, people should also pay attention when using hydraulic lifting platforms, otherwise they can easily malfunction, which may lead to serious consequences. So what are the common faults of hydraulic lifting platforms?
In this machine, and the parts between the brushes must be kept clean. Regular inspections are also required between the various bearings inside the machine, especially when adding butter to the bearings. If the butter is insufficient, it will cause severe wear and tear during the operation of the bearings, affecting the service life of the machine. There are various wires and cables inside the machine, and after a period of use, it is necessary to inspect the wires and cables. If any damage is found to the wires and cables, it is necessary to repair or replace them. Regularly check whether the screws at this connection are loose. If any screws are found to be loose, they should be tightened. Some screws must meet certain torque requirements. In the absence of relevant professional equipment, you can use professional equipment to tighten the screws at the repair shop. It is necessary to ensure that the screws meet the corresponding torque requirements.
During use, the elevator should be placed on a solid and flat ground to prevent tipping during operation. Press&quo; Rising; Or&quo; Descending; Press the button to frequently check and maintain the various components of the elevator when lifting the workbench. If the workbench does not move, it should be immediately stopped for inspection. When the working pressure of the electric elevator is found to be too high or the sound is abnormal, it should be immediately shut down for inspection to avoid serious mechanical damage; Regularly check the working status of the shaft pin every month. If any loose shaft pin or screw is found, it must be locked tightly to prevent accidents caused by the shaft pin falling off.
Installation requirements.The power unit adjustment,Hague8-meter hydraulic lifting platform, whether it is a scissor type lifting platform or a guide rail type lifting cargo elevator, is composed of the power unit and the oil cylinder. The power unit has four outlets during production, which can be adjusted to increase or decrease the hydraulic oil flow rate of the oil cylinder. We can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow rate; What factors will affect the lifting speed of hydraulic elevators? The longer the hydraulic oil pipe, the longer the lifting time. Therefore, during installation, the length of the oil pipe should be minimized as much as possible within the allowable range of the design; On the basis of adjusting the power unit, the size of the oil pipeline can also be adjusted, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.
How to install and use the bearings of the elevator? During the process of using the bearing device of the elevator, we cannot always ensure that the bearing device has the right orientation, which inevitably leads to some devices not being in place or bearing displacement. Once these problems occur in the device, it will cause the clearance between the bearings to become too small, and then make it impossible for the inner and outer rings of the bearings to be in the same rotation center. So it is necessary to use specialized tools when installing bearings, and in the future, it is also necessary to use a testing instrument to test the bearing installation, in order to ensure the success of the bearing installation.
Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.
The guide rail type cargo elevator has been inspected and debugged before leaving the factory, only the power supply needs to be connected,HagueHydraulic mobile lifting platform, and the hydraulic and electrical systems do not need to be adjusted.
Excellent service.The load capacity of goods and the tonnage of goods transported at once also affect the speed of lifting and lowering. Achieving the excellent value of the lifting platform for transporting goods is a guarantee of speed. If the weight is too heavy, it affects the speed. If the goods are too light, it also affects the normal transportation time.
The reason for the price of aluminum alloy lifting platforms is that hydraulic pumps are also a factor affecting the flow of hydraulic oil. Using hydraulic pumps that have been used for too long can easily lead to problems. When the speed of the hydraulic elevator platform slows down, it is necessary to check whether the oil supply flow rate of the hydraulic pump remains unchanged. If there is an invention problem, contact the manufacturer in real time to avoid exceeding the warranty period.
Drain and discard the hydraulic oil from the hydraulic lifting cargo elevator. For the outdoor guide rail elevator, tighten the joint and remove the oil filter. After cleaning, and then return it to the oil tank and connect the pipeline.
Hague.For the safety performance of high-altitude work platforms, scientific processes, and strict management to ensure production. When in use, people, the environment, and machines are the three major links of high-altitude operations, Jiuyi briefly describes the precautions for using high-altitude operation platforms: high-altitude operators must hold a health certificate. Individuals suffering from intentional, high-pressure, or mental illness are not allowed to engage in high-altitude work tasks. Staff are not allowed to engage in high-altitude work while drinking alcohol or feeling mentally drained.
Working at heights is a common practice nowadays, but it also has a certain degree of danger. So people invented hydraulic lifting platforms which are more convenient to help people complete high-altitude operations. However, people should also pay attention when using hydraulic lifting platforms, otherwise they can easily malfunction, which may lead to serious consequences. So what are the common faults of hydraulic lifting platforms?
When encountering overheating in the hydraulic elevator motor, it is necessary to stop it in a timely manner, eliminate the fault and continue running. The motor bearings should be in good condition.