such as forcefully opening the door inside the car
Aircraft weighing tens or hundreds of tons in the elevator hangar are vertically lifted onto the airport runway
There are many similar situations in daily life, causing the circuit to disconnect and forcing the elevator to stop, resulting in people being trapped. For example, if the elevator frequently enters and exits during decoration and falls into the crack of the door, the elevator hall door may not be tightly closed, and after several consecutive doors are opened and closed, the elevator will stop. Professional quality assurance for home elevator manufacturers. Discount activities are underway, and new and old customers are welcome to come for consultation
Polly.The shaft for updating the old elevator: The measurement of the shaft for the old elevator is the same as the shaft that has just been constructed. When the old elevator is not yet in use, try to obtain relevant data outside the shaft, floor height,PollyRear flip hydraulic plate flipper, and net size of the door opening. There are two situations when the old elevator is not yet in use: a. When the old elevator can start: in this case, the elevator technician must cooperate in measuring the shaft! And be sure to pay attention to safety! The elevator technician opens the hall door on the first floor and initiates maintenance operations to drive the car above the second floor. The measurement personnel open the floor door on the first floor to measure the pit data, paying attention to recording the pit size and the wall structure of the first floor, such as whether the hall door is centered, whether there are brackets, whether there are special structures on the shaft wall, the spacing between ring beams, and the position of embedded parts. Then, the measuring personnel and elevator technicians take the elevator to the top floor. After measuring the machine room, the measuring personnel, with the cooperation of the technicians, go up to the car roof and start the elevator at a maintenance speed. When the car roof is slightly lower than the sill of the second floor hall door, the parking lot stops. During this process, the measuring personnel observe and measure the full travel of the shaft from the top floor mainly the height of the floor, while recording the measurement (safety must be paid attention to, and special attention should be paid to moving parts such as counterweights and wire ropes).
Aircraft weighing tens or hundreds of tons in the elevator hangar are vertically lifted onto the airport runway
.The elevator stops on the first floor and the door does not move: the fire emergency landing function of the elevator is triggered by smoke or thermal sensors inside the building.
Slide elevators are installed inside buildings and are often used parallel to buildings and sidewalks
These phenomena are not elevator malfunctions. When the elevator is fully loaded, the leveling reference position needs to be re determined.
b. When the old elevator cannot start: due to the inability to enter the shaft, limited data can only be obtained from outside the shaft to determine whether it is non-standard (if there is a high platform in the machine room, the plane size of the shaft can be measured in the machine room, but it is not accurate enough) for elevator quotation negotiation reference. In this case, the signing of the contract should state that the shaft rectification and costs are the responsibility of the user. For uncertain shaft structures and dimensions, users should be reminded to provide them to the elevator after the old elevator or notify the elevator to take measurements before the new elevator is put into operation.
Mine elevators are used for transporting personnel and goods in mines. Special elevators are designed for special environmental conditions, such as explosion-proof,PollyVertical obstacle free lifting platform, anti-corrosion, and heat-resistant elevators
Welcome to inquire.Elevator does not close the door or repeatedly opens and closes the door: there are debris blocking the light curtain or door contact plate at the entrance or sill.
The elevator stops on a certain floor for a long time without moving or responding to external calls: it is possible that the elevator administrator has activated the driver operation function.
The gantry elevator is used in the door legs of large gantry cranes to transport workers and maintenance components inside the gantry crane
The difference between home elevators and ordinary public elevators is that the focus of home elevators and ordinary public elevators is different, with some indicators significantly reduced. For example, the load capacity of home elevators does not exceed 400kg, which is much lower than that of ordinary public elevators. Home elevators do not need to consider the issue of passenger flow and the lifting speed is slower, ensuring safety. The lifting speed is generally between 0.3 to 0.4m/s, and running smoothly.
Economic management.Will the elevator quickly fall during a power outage& mdash;& mdash; Some movies and TV dramas often mislead the public into thinking that if the elevator loses its power, abbreviated as Variable Voltage Variable Frequency in English, is based on the principles of electrical engineering. The speed and torque of the motor are directly proportional to the frequency and voltage amplitude of the AC power supply, achieving accurate speed regulation and control of the motor. This speed regulation technology ensures smooth elevator operation, accurate leveling, and flexibility.
2. Different types of civil engineering traction elevators, screw elevators, and hydraulic elevators have different requirements for civil engineering. Common traction elevators require a certain amount of hoistway space, which can be made of concrete,PollyStage electric elevator, steel structure hoistways, and glass curtain walls to create sightseeing elevators; The depth of the pit should be at least 50cm or more; Additionally, there are certain requirements for the height of the top floor.
Polly.When encountering abnormal elevator operation, you can call the repair hotline to consult with the maintenance personnel or inform the service center to handle it. Do not take unauthorized measures to avoid causing greater harm to the elevator or even causing casualties.
The elevator suddenly opens the door and does not move after leveling, but automatically resumes operation after a few minutes: The elevator (escalator) has been running for too long, and the motor overheats. To prevent burning out, the motor cools down and automatically resumes operation.
2. Different types of civil engineering traction elevators, screw elevators, and hydraulic elevators have different requirements for civil engineering. Common traction elevators require a certain amount of hoistway space, which can be made of concrete, steel structure hoistways and glass curtain walls to create sightseeing elevators; The depth of the pit should be at least 50cm or more; Additionally, there are certain requirements for the height of the top floor.