HengshuiHydrau
HengshuiHydrauWhen a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
Hengshui.The lifting platform truck should be placed in a trench position and corresponding anti slip measures should be taken; Remove the gearbox of the equipment, remove the axle oil box, and take out the lower bearing and oil suction device; Slowly test drive and check if the surface around the axle diameter is severely damaged; If the damage is severe and tungsten is occupied, it should be polished smooth with an oilstone; Under the electric motor place the sleeper on the trench edge on the inner side of the steel rail, use a jack to regularly pull the electric motor and remove the upper tile; How to solve the damage of important equipment in the lifting platform car? Check the status of the bearing pads and oil absorbers investigate the cause of the damage, replace the bearing pads, install a new oil suction device on the axle oil box and clean the axle oil; Gear oil of gear box shall be as specified; Burning of axle box bearings is a common occurrence,HengshuiHydraulic lifting platform fixed hydraulic, which is the burning of outer bearings. In severe cases, it can cause the axle box and wheel set to be fixed together, affecting equipment operation.
When conducting a resistance check, it is necessary to disconnect the power supply. At this time, the circuit principle can be used to measure and then measure the magnitude of the resistance value
.The above detailed introduction, I believe everyone has a comprehensive understanding and understanding of the use of hydraulic elevators, they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, and it is strictly prohibited to carry people. If the electric lifting platform truck carries people during use, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
Of course, customization can also be made according to customer needs. If the carrying capacity is relatively large, it can be selected based on its model, which will result in more single shipments. When choosing an electric elevator, you also need to consider its climbing ability. If it has strong climbing ability, it can be suitable for various floor heights, making it more convenient to use. Because the height of the floor has a certain impact on the climbing of electric elevators, as current climbing has undergone safety testing. Attention should also be paid to the climbing speed of the electric elevator to reduce the time of porter. Long term hydraulic lift truck prices are not reversed by manufacturers to avoid price differences, with prices higher than the market
For lifting platform vehicles without manned protection it is strictly prohibited to carry people during use. At the same time, attention should be paid during use to prevent damage to hands, feet, and clothing.
Hydraulic loading elevators must strictly carry out load-bearing operations in accordance with regulations. Otherwise, it may harm people and objects!
The above detailed introduction, I believe everyone has a comprehensive understanding and understanding of the use of hydraulic elevators, and these details cannot be ignored during the use process.
Finance Department.In the past, in large workshops, if goods had to be transferred from one place to another, it would be very expensive. For loading, unloading, and transferring 2 tons of goods, it would require 10 people to work continuously for several hours, using forklifts to operate and multiple forklifts to work simultaneously for one or two hours. Moreover, using forklifts also required professional forklift drivers, and the cost of using them was often high. Is there any way to do this, Can it meet both rapid loading and unloading of goods and low-cost needs? Of course there is, that is the application of fixed loading and unloading platform trucks. A fixed loading and unloading platform truck is an auxiliary equipment that mainly completes the rapid loading and unloading of goods. It has an adjustment function, and the truck has a certain height to cross when transporting goods from the warehouse to the truck. However, a fixed loading and unloading platform truck can adjust the height and serve as a bridge to connect the truck and warehouse meeting a large number of cargo handling needs, But such a large workload requires only one operator to operate, greatly saving labor costs and manpower, improving the production efficiency of the enterprise. Professional hydraulic lift truck manufacturer with high prices, service, on-site settlement, and honest operation!
Of course, customization can also be made according to customer needs. If the carrying capacity is relatively large, it can be selected based on its model, which will result in more single shipments. When choosing an electric elevator, you also need to consider its climbing ability. If it has strong climbing ability, it can be suitable for various floor heights, making it more convenient to use. Because the height of the floor has a certain impact on the climbing of electric elevators, as current climbing has undergone safety testing. Attention should also be paid to the climbing speed of the electric elevator to reduce the time of porter. Long term hydraulic lift truck prices are not reversed by manufacturers to avoid price differences, with prices higher than the market
From this, it can be seen that the hydraulic lifting platform truck needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.
Especially when its pipes are in use they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, and it is strictly prohibited to carry people. If the electric lifting platform truck carries people during use, the lifting platform is equipped with railings or anti crack valves, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
Variable cost.Especially when its pipes are in use, they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, it is not allowed to carry people during use, and it is strictly prohibited to carry people. If the electric lifting platform truck carries people during use, the lifting platform is equipped with railings or anti crack valves,HengshuiSmall hydraulic lifting and leveling, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
Safety protection components in order to ensure safety production work, it is essential to install a lifting platform car for proper protection. The main protective accessories include safety belts, guardrails, protective covers, platform car stairs, etc.
The reason why many fields choose to use the electric elevator is that it can not only save manpower but also facilitate people's life in the process of use. The important thing is to solve the handling work, so that the electric elevator can be used to carry goods upstairs and downstairs. When transporting goods, the first thing everyone should pay attention to is its carrying capacity. Generally, around 500 kilograms of goods can be transported, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.
When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
The function of a fixed loading and unloading platform truck. The fixed loading and unloading platform truck meets the loading and unloading needs of goods, and has good load-bearing effect, convenient loading and unloading, low consumption, and easy operation. The stability of the loading and unloading process is strong, and the height can be adjusted and lifted to a suitable position to meet the loading and unloading of goods. The later maintenance is in place and the maintenance cost is low.