ZhuozhouMast tIt is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time
Method for hydraulic oil leakage in aluminum alloy elevator: Check if the pipe joints are loose and try to tighten them. Check if the viscosity of the hydraulic oil used is too low. When checking the leakage point of the hydraulic oil system, generally, the place where hydraulic oil seeps out is the leakage point, but it is not ruled out that the leaked hydraulic oil may accumulate along the pipeline deviating from the leakage point. Therefore, it is important to carefully search during inspection. High priced aluminum alloy elevator manufacturers of various specifications welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!
Zhuozhou.Check if the aluminum plate is deformed. Although the aluminum plate has strong resistance to impact, it also has certain limits. When encountering strong lateral sharp object impacts, the aluminum plate will also deform slightly, causing the phenomenon of jamming between the aluminum plate and the aluminum plate, which must be avoided during normal use.
The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
.Secondly,ZhuozhouProduction of aluminum alloy lifting platforms, frequent voltage instability can directly burn out the power unit motor. The consequences of motor burning are very serious, which can lead to an instant decrease in pressure. If the equipment is not equipped with safety devices such as relief valves or explosion-proof valves, it can cause the lifting equipment to fall leading to accidents. At the same time, replacing a new power unit also requires a certain cost.
Aluminum alloy elevator is a multifunctional high-altitude work equipment that uses electric hydraulic transmission. It has the advantages of light weight, self walking, electric starting self supporting legs, simple operation, large working surface, and can safely and stably carry out high-altitude work. After using the mobile aluminum alloy elevator for a period of time, it requires overall maintenance. Below is an introduction to the maintenance precautions for the mobile aluminum alloy elevator.
Users can choose the power mode and configuration according to their usage range: the power system includes: DC power supply, single-phase or three-phase power supply, diesel engine. Walking: assisted self-propelled, two wheel traction, self driving, and car modification. Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand cranked outriggers, and pull-out outriggers. System: explosion-proof electronic control system, remote control system, PIC system. Hydraulic pump station: domestic lifting platform dedicated pump station, imported pump station from Italy with external protective devices: organ cover type, mesh type, and iron plate sealed type.
With the continuous development of the economy, and increasing productivity, aluminum alloy elevators play an important role in high-altitude operations.
Generally, this job is what operators should do after each operation.
Firstly the maintenance process should be carried out on the premise of ensuring the safety of staff. Before repairing the aluminum alloy elevator, and the power must be verified and hung up; No power transmission the power must be disconnected, people working&# quo; Identification plate for. During the maintenance process, it is not allowed to disconnect the grounding wire of the aluminum alloy elevator. If it is necessary for maintenance work, after the maintenance is completed, the grounding wire must be connected before the power test can be conducted. When replacing spare parts for aluminum alloy elevators, it is necessary to ensure that the spare parts are intact and of the same model. Items such as valves and seals should be placed in dry and dust-free packaging. When hydraulic aluminum alloy elevator maintenance requires entering the platform for internal work, after the aluminum alloy elevator is lifted, the working surface of the aluminum alloy elevator must be fixed or supported firmly with a crane or other equipment,
Bidding.On the friction surface there should be no dirt present, and any dirt must be washed off with gasoline or thinner.
Performance characteristics of Xiangte aluminum alloy elevator: The hydraulic system of aluminum alloy elevator products is generally equipped with safety protection devices such as anti fall,ZhuozhouMast type aluminum alloy lifting platform, overload, and warning lights or bells for the operation of the lifting platform, as well as safety switches that close the lifting platform circuit when the door is open. Extremely generous, operators can operate in multiple layers, jog or safe mode.
Hydraulic lifting platforms can be divided into: four wheel mobile, two wheel traction, car modification, car type, auxiliary self-propelled, and lifting heights ranging from 4 meters to 18 meters. This series of products has a load capacity of 0.1 to 0.8 tons, and can also be customized according to user requirements, with a high load capacity of up to 10 tons.
Double masted aluminum alloy lifting platform: a new generation product of the design, made entirely of high-strength aluminum profiles. Due to the high strength of the profiles, the deflection of the lifting platform is minimal. Adopting a double mast column structure, it has a large load capacity, a large platform area, excellent stability, flexible operation,ZhuozhouLifting aluminum alloy ladder, and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. This elevator is widely used for three masted aluminum alloy lifting platforms: three sets of masts support the operation platform for synchronous lifting, and the support structure is the same as a single masted platform, with super large load capacity and work stability. The overall lifting guardrail device has good strength and greatly reduces the height of the entire machine during transportation. It is very convenient for loading and unloading, and can be assembled or disassembled in one lift. The elevator has a strong load-bearing capacity and is suitable for two people (who can carry a certain amount of weight tools and materials) to climb high at the same time; Various non-standard products can also be customized according to different environments to meet different needs.
quality.Machine manufacturers and other related businesses. Merchants with this business are welcome
Hazards of moving parts of aluminum alloy elevators: This hazard mainly comes from dangerous parts of mechanical equipment, including rotating parts such as rotating shafts, protrusions and holes, rotating connectors, core shafts, as well as rotating fixtures, fan blades, flywheels, do not stay near the exhaust pipe of the working engine for a long time.
Zhuozhou.Advantages: Due to the wide selection of electronic control switches, the aluminum alloy elevator with remote operation system can be operated remotely even on harsh construction sites, improving the comfort of operation and convenient walking. On the basis of traditional aluminum alloy elevators, steel bar transportation devices and concrete transportation devices are installed, concrete, and workers, greatly improving construction efficiency; The optional advanced stepless frequency control system enables the elevator to achieve stepless speed regulation of 0-60m/min.
Hydraulic aluminum alloy elevators operate up and down, and can provide us with a safe and stable platform. We can provide security for our safety when working at heights.
When encountering overheating in the motor, it is necessary to stop it in a timely manner and continue running after troubleshooting. The motor bearings should be in good condition.