GathviejoStainless steel plate stainless steel coilWhat are the selection criteria

What must be done is to clean up on time. The residue on the top must be removed immediately. Otherwise, it is easy to change qualitatively on the vegetable board. It is not necessary to expose to the sun for a long time. It is OK to put it in a cool and ventilated place.

This is also one of the reasons why some consumers often encounter oxidation when using stainless steel products. Some consumers do not operate properly in the use and maintenance of products, especially some stainless steel pipe products used in the food and chemical equipment industry

Gathviejo.The packaging itself requires manufacturing costs, and the cost of packaging requires labor costs, the sum of which exceeds the weight of a single bag.

It is concluded that the corrosion resistance of duplex stainless steel is equivalent to that of 316L stainless steel, but the mechanical properties are better than 316L, and the cost is lower than that of 316L and 4462.

.The oxide scale of stainless steel pipe becomes loose after pretreatment, and then it is easy to remove after pickling. Pretreatment can be divided into the following: alkaline salt melting treatment. The alkaline melt contains 87% hydroxide and 13% salt. The proportion of the two in the molten salt should be strict so that

Precipitation; After each use, wash with 50 to 60 ℃ boiling water and dry immediately after washing. Other dishes should also be cut into shredded potatoes,

Continuous casting shall be adopted for stainless steel pipe fittings, so as to improve the comprehensive yield. In addition, in combination with out of furnace refining, the production efficiency is significantly improved, and the blank opening process is omitted, which saves a lot of energy consumption.

Stress corrosion cracking (SCC) refers to the cracking caused by the combined action of stress corrosion stress (mainly tensile stress) and corrosion of austenitic stainless steel. Austenitic stainless steels are prone to stress corrosion in corrosive media containing chloride ions. When

Corrosion kinetics curve; Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the morphology, structure and element content of the test pieces. The high temperature oxidation resistance and high temperature KCl vapor corrosion resistance of four new stainless steel materials, traditional TP316 materials and high chromium materials were compared. Result table

After each application of the cutting board (especially after cutting meat stuffing), scrape off the food residue and residual juice on the surface, brush with clean water, and then put it into normal saline (the concentration value is about 15%) to soak for 2 hours, and then take it out for drying. That can not only remove bacteria, but also avoid cracking of the cutting board.

Welcome to inquire.Stainless steel plate has super fire resistance, heat resistance and corrosion resistance, and is also widely used.

However the effect of different stages varies with the stainless steel plate and process.

A very thin chromium film is formed on the surface, which is isolated from the corrosion resistance of oxygen invaded in the steel.

Stone,GathviejoSupplier of stainless steel strip, wood and other materials are easily moldy or weathered when the kitchen is flooded for a long time. Other metal materials are not suitable for wet kitchen decoration. Therefore,GathviejoPrice of 316L stainless steel pipe, stainless steel metal is far more suitable for cabinet decoration than other materials. However, 201 and 304 are not

Quality improvement.If rust is found on the surface of stainless steel plate the surface can be brushed with stainless steel plate wax. This product is specially used for rust prevention treatment of stainless steel. After a period of time, polish and clean the wax, and then clean the wax on the surface

According to the steel structure, austenite ferrite ferrite martensite and precipitation hardening note: precipitation hardening (precipitation strengthening): refers to the dispersion and distribution of solute atoms in the supersaturated solid solution and / or desolved particles in the

Technology is one-time forming, and nitrogen protection is also added during welding.

Gathviejo.Improving people's living standards plays an unparalleled role.

In this process, the following key points should be paid attention to: during the welding process,Gathviejo316L stainless steel pipe supplier, the correct included angle should be maintained between the welding handle, welding wire and weldment, and the ideal rake angle of the welding handle nozzle is 70 DEG& Mdash; 80° The included angle between the welding wire and the surface of the weldment is 15 DEG& Mdash; 20°; Correct weld pool temperature and change welding

The same, but the orientation is reversed, so the two working pressures offset each other.