EmerodDouble m
EmerodCustomizMethod: Check if the hydraulic oil in the mailbox is sufficient; Check if the oil filler cap of the fuel tank is excessively sealed, causing difficulty in oil pump suction. Check if the connection of the oil pump suction pipeline is loose to prevent air from the oil pump; Check whether the motor, cover, etc. are displaced, whether the fixing screws are loose and whether the ambient temperature of the equipment used meets the specified usage conditions. Air, check whether the motor, cover, etc. are displaced, whether the fixing screws are loose, and whether the ambient temperature of the equipment used meets the specified usage conditions.
Check if the power supply voltage is below the allowable value.
Emerod.For example, if you can carefully check whether the switch is defective, how can you improve its service life? Below is a detailed explanation for everyone.
Pay attention to checking each steel wire rope for broken wires and loose strands. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
.Secondly, frequent voltage instability can directly burn out the power unit motor. The consequences of motor burning are very serious, which can lead to an instant decrease in pressure. If the equipment is not equipped with safety devices such as relief valves or explosion-proof valves, it can cause the lifting equipment to fall, leading to accidents. At the same time replacing a new power unit also requires a certain cost.
Working on an aluminum alloy elevator workbench. Must wear safety belts, helmets, overload,EmerodAluminum alloy high-altitude lifting platform, and power outage. The entrance and exit of the table are equipped with hanging chains or crossbars, guardrails,Emerod10 meter aluminum alloy elevator, and warning lights or bells for the operation of the lifting platform, as well as safety switches that close the lifting platform circuit when the door is open. Extremely generous, operators can operate in multiple layers, jog or safe mode.
Secondly, frequent voltage instability can directly burn out the power unit motor. The consequences of motor burning are very serious, which can lead to an instant decrease in pressure. If the equipment is not equipped with safety devices such as relief valves or explosion-proof valves, it can cause the lifting equipment to fall, leading to accidents. At the same time, replacing a new power unit also requires a certain cost.
Introduction to Aluminum Alloy Elevator:.
Introduction to aluminum alloy elevator: Aluminum alloy elevator is a fixed transportation equipment that lifts items from one height to another. Due to the large weight and volume of the lifted object, it is safe and stable. It can be used as a specialized hydraulic lifting platform product for transporting goods between floors of buildings, with the main function of transporting various work floor goods up and down; At present, aluminum alloy elevators are mostly used in the market for lifting cars in three-dimensional garages and garage floors.
supply.Advantages: Due to the wide selection of electronic control switches, the aluminum alloy elevator with remote operation system can be operated remotely even on harsh construction sites, improving the comfort of operation and convenient walking. On the basis of traditional aluminum alloy elevators, which can transport steel bars, concrete, greatly improving construction efficiency; The optional advanced stepless frequency control system enables the elevator to achieve stepless speed regulation of 0-60m/min.
It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time
An aluminum alloy elevator equipment consisting of a walking mechanism hydraulic mechanism,EmerodAluminum alloy high-altitude lifting platform, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, which can meet the different needs of different heights, that is, press and stop, making high-altitude operations simple and feasible.
Quality inspection report.Problem: The power indicator light of the aluminum alloy elevator is not on, and the lifting does not operate. Method: Check whether the power cord is correctly connected to the power socket; Check whether the circuit breaker switch is closed and whether the leakage protection switch is tripped.
The equipment voltage is 24V DC, effectively ensuring personal safety.
Firstly, the maintenance process should be carried out on the premise of ensuring the safety of staff. Before repairing the aluminum alloy elevator, the power must be disconnected, and the power must be verified and hung up; No power transmission, people working&# quo; Identification plate for. During the maintenance process, it is not allowed to disconnect the grounding wire of the aluminum alloy elevator. If it is necessary for maintenance work, after the maintenance is completed, the grounding wire must be connected before the power test can be conducted. When replacing spare parts for aluminum alloy elevators, it is necessary to ensure that the spare parts are intact and of the same model. Items such as valves and seals should be placed in dry and dust-free packaging. When hydraulic aluminum alloy elevator maintenance requires entering the platform for internal work, after the aluminum alloy elevator is lifted, the working surface of the aluminum alloy elevator must be fixed or supported firmly with a crane or other equipment
Emerod.Each box, distribution box, etc. should be kept clean regularly and dust on electrical equipment should be promptly cleaned.
The problem is that the power indicator light is on, but there is&quo; in the electrical box when the up button is pressed; Clacking sound&rdquo, Does the platform not rise or can only rise to a limited height?
The garage door should be opened or the exhaust device should be opened. So that the exhaust gas can be stored in the garage at any time. Even if working outdoors. Also, do not stay near the exhaust pipe of the working engine for a long time.