VeronaAluminumThe main components of the Hunter hydraulic fixed elevator are: 1. The shaft part is a closed or mesh frame enclosed by buildings or lightweight steel structures, with steel guide rails installed on both sides of the interior. 2. The driving part is equipped with a hydraulic drive motor, oil pump, and safety valve, A small oil tank for hydraulic components such as speed control valves and directional valves: 3. The oil cylinder part: It is composed of one or more oil cylinders of the lifting oil cylinder straight top platform or lifting shear fork frame: 4. The door system part: It is a closed or mesh platform door or landing door system composed of steel structure, with manual and automatic doors. Generally open platforms do not have doors. 5. The electrical part: It includes power, Composition of safety and lighting devices: 6 Platform parts: It is a steel structure platform that carries heavy objects signal, which can be closed (i.e. cabin type) or open, with guide rollers or guide shoes installed on both sides. The bottom of the platform can be connected to a lifting oil cylinder or a lifting shear fork shaped steel frame. When we use aluminum alloy elevators, we need to regularly inspect, maintain, and maintain them, which can not only extend the service life of the aluminum alloy elevator, Can make it work with greater power! For example,VeronaJiugu aluminum alloy elevator,VeronaTilting aluminum alloy elevator, the transmission part should have sufficient oil, and vulnerable parts must be regularly inspected, repaired, especially parts that frequently vibrate, such as slewing bearings and lifting arm connecting bolts should be checked for looseness. If there is looseness, it must be tightened or replaced immediately. Next, let's take a look at the regulations for the maintenance time of aluminum alloy elevators: daily maintenance (carried out per shift).
It is strictly prohibited to damage the elevator. Brake fluid has a damaging effect on the paint film of aluminum alloy elevators. It can quickly dissolve the paint film. Simultaneously. Brake fluid is also harmful to the eyes. It is reminded that if it splashes into the eyes, it must be immediately rinsed with clean water.
Verona.The fault diagnosis equipment on the elevator can inform the operator of possible errors. The chassis is high and suitable for walking on rough surfaces. Planning is practical, reliable, and easy to repair and maintain. Diesel powered models have two wheel, four wheel drive, and steering. Free turning equipment. Urgent descent system. The operation height ranges from 4 meters to 22 meters, with advanced equipment and high-power power. Professional aluminum alloy elevator manufacturers and other various types of products are complete, best-selling at home and abroad, and the equipment has a long service life! The industry leader in product wire products,VeronaDouble column aluminum alloy elevator, welcome to inquire
When repairing an aluminum alloy elevator, in order to protect the safety of workers and ensure the repair effect, made entirely of high-strength aluminum profiles. Due to the high strength of the profiles, the deflection of the lifting platform is minimal. Adopting a double mast column structure, it has a large load capacity, a large platform area, excellent stability, flexible operation, and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. This elevator is widely used for three masted aluminum alloy lifting platforms: three sets of masts support the operation platform for synchronous lifting, and the support structure is the same as a single masted platform, with super large load capacity and work stability. The overall lifting guardrail device has good strength and greatly reduces the height of the entire machine during transportation. It is very convenient for loading and unloading, and can be assembled or disassembled in one lift. The elevator has a strong load-bearing capacity and is suitable for two people (who can carry a certain amount of weight tools and materials) to climb high at the same time; Various non-standard products can also be customized according to different environments to meet different needs.
Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated.
It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time
With the continuous increase of our productivity and the continuous improvement of our lives the demand for aluminum alloy elevators is also increasing. The application of aluminum alloy elevators in every corner of our lives will bring us objective benefits.
Attention: When replacing the adjusting steel wire rope, the half round head bolt should be unscrewed first to allow the moving nut to roll together with the force bolt, so as not to move the nut up and down too much and damage other components. After replacing the safety wire rope of the aluminum alloy elevator platform, adjust the position of the collision rod from the beginning to reach the ultra-high limit position. The limit switch of the aluminum alloy elevator platform should be regularly inspected and replaced or repaired in case of damage.
The scientific design schemes for aluminum alloy elevators mainly include leveling and locking circuits, telescopic balance circuits, variable amplitude balance circuits, emergency lowering systems, etc. In order to prevent sudden damage to the hydraulic system or pipelines of the platform due to accidents, and to ensure that the workbench does not experience situations that endanger the safety of personnel and equipment such as sudden arm fall or workbench overturning, we have designed different solutions for each system according to its different conditions.
Inspection requirements.Hydraulic aluminum alloy elevators operate up and down, as this not only reduces the service life but also poses safety hazards.
Three masts aluminum alloy elevator: The main structure is made of high-quality high-strength aluminum profiles, with super large load capacity and working stability. The overall lifting guardrail device has good strength, greatly reducing the overall height during transportation, and making loading and unloading convenient. This machine has strong load-bearing capacity and is suitable for 2-3 people to climb heights simultaneously.
After working for 10000 hours, the mechanical and electrical systems of the elevator will be overhauled.
where.After working for 10000 hours, the mechanical and electrical systems of the elevator will be overhauled.
There will be brushes in this machine, and the parts between the brushes must be kept clean.
Machine manufacturers and other related businesses. Merchants with this business are welcome
Verona.The protected leg structure makes work safer and can be used for lifting and lowering operations close to the working face.
The reduction gearbox, gearbox, external meshing gear and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table. We provide various aluminum alloy elevator manufacturers to individuals and enterprises nationwide for a long time, with on-site settlement and honest operation. We have offices in various regions and can cooperate for a long time
Method for hydraulic oil leakage in aluminum alloy elevator: Check if the pipe joints are loose and try to tighten them. Check if the viscosity of the hydraulic oil used is too low. When checking the leakage point of the hydraulic oil system, generally, the place where hydraulic oil seeps out is the leakage point, it is important to carefully search during inspection. High priced aluminum alloy elevator manufacturers of various specifications welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!