BazhouAluminumStrictly follow the operating instructions of the aluminum alloy elevator for safe use, and strictly prohibit illegal operations.
After 5000 hours of operation of the elevator, carry out medium maintenance on the mechanical and electrical systems.
Bazhou.There are more and more types of aluminum alloy elevators, including single masted aluminum alloy elevators, double masted aluminum alloy elevators, three masted main aluminum alloy elevators, four masted aluminum alloy elevators, and multi masted aluminum alloy elevators. The following is a specific introduction and explanation:.
The main components of the Hunter hydraulic fixed elevator are: 1. The shaft part is a closed or mesh frame enclosed by buildings or lightweight steel structures, with steel guide rails installed on both sides of the interior. 2. The driving part is equipped with a hydraulic drive motor, oil pump, and safety valve, A small oil tank for hydraulic components such as speed control valves and directional valves: 3. The oil cylinder part: It is composed of one or more oil cylinders of the lifting oil cylinder straight top platform or lifting shear fork frame: 4. The door system part: It is a closed or mesh platform door or landing door system composed of steel structure, with manual and automatic doors. Generally, open platforms do not have doors. 5. The electrical part: It includes power, signal Composition of safety and lighting devices: 6 Platform parts: It is a steel structure platform that carries heavy objects, which can be closed (i.e. cabin type) or open, with guide rollers or guide shoes installed on both sides. The bottom of the platform can be connected to a lifting oil cylinder or a lifting shear fork shaped steel frame. When we use aluminum alloy elevators, we need to regularly inspect, maintain, and maintain them, which can not only extend the service life of the aluminum alloy elevator, Can make it work with greater power! For example, the transmission part should have sufficient oil, and vulnerable parts must be regularly inspected, repaired, or replaced. Mechanical bolts, especially parts that frequently vibrate, such as slewing bearings and lifting arm connecting bolts,BazhouDouble mast aluminum alloy lifting frame, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately. Next, let's take a look at the regulations for the maintenance time of aluminum alloy elevators: daily maintenance (carried out per shift).
.. Before the maintenance of the hydraulic aluminum alloy elevator starts, the tools used must be counted. After the maintenance is completed, the tools should be classified and organized, and counted to prevent the tools used for maintenance from being left inside the equipment, especially in the distribution box. When repairing the hydraulic system of the aluminum alloy elevator, it is necessary to keep the maintenance site clean and dust-free. When repairing and fastening screws for aluminum alloy elevators, it is necessary to use the correct diagonal first. When tightening screws, it is necessary to count the number of maintenance personnel to ensure that there is no one inside the aluminum alloy elevator. This is very necessary for the maintenance of large fixed hydraulic elevators. After counting the number of people, inspecting and repairing the equipment and the maintenance site, the power transmission test can only be carried out. After the maintenance of the aluminum alloy elevator is completed, the equipment maintenance record must be filled out. The maintenance record should include the equipment maintenance date, the personnel participating in the maintenance, the maintenance items, the brand, model and specification of the replaced parts, the effectiveness of the maintenance, and whether the equipment still has problems after the maintenance is completed.
Hydraulic aluminum alloy elevators operate up and down, and can provide us with a safe and stable platform. We can provide security for our safety when working at heights.
Performance characteristics of Xiangte aluminum alloy elevator: The hydraulic system of aluminum alloy elevator products is generally equipped with safety protection devices such as anti fall, guardrails and power outage. The entrance and exit of the table are equipped with hanging chains or crossbars and warning lights or bells for the operation of the lifting platform, as well as safety switches that close the lifting platform circuit when the door is open. Extremely generous, jog or safe mode.
Each box, etc. should be kept clean regularly and dust on electrical equipment should be promptly cleaned.
If it cannot be used normally, shortness of breath, nausea and vomiting, body weakness and dizziness, psychological confusion and even brain damage. In severe cases, it can cause death, such as starting the engine of the equipment in the garage.
property right.The aluminum alloy elevator with strong controllable performance is easy to operate and has high accuracy, which can meet the different needs of different heights, that is, press and stop, making high-altitude operations simple and feasible.
After 1500 hours of operation of the elevator, minor repairs will be carried out to the mechanical and electrical systems. Professional aluminum alloy elevator manufacturer is safe, environmentally friendly, and economical! Our products are exported to foreign countries and highly trusted
When installing, disassembling, and adjusting the rotating mechanism, it is important to ensure that the centerline of the reducer of the rotating mechanism is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable.
Aluminum alloy elevators are a product of modern high-altitude operations. During their development, the performance and quality of aluminum alloy elevators have continuously strengthened, becoming the main force of modern high-altitude operations. So, how much do you know about their scientific design solutions?
High quality and low price.Hydraulic lifting platform products are divided into curved arm hydraulic aluminum alloy elevators, scissor fork hydraulic aluminum alloy elevators, mast hydraulic aluminum alloy elevators, and straight arm hydraulic aluminum alloy elevators according to their working modes. Hydraulic aluminum alloy elevator is a replacement product of folding arm aluminum alloy elevator (lifting platform) and scissor fork aluminum alloy elevator (lifting platform). It can be widely used for the decoration and decoration of stations,BazhouLifting platform aluminum alloy, docks, airports, hotels, posts and telecommunications, municipal gardens,BazhouAluminum alloy elevator single column, grain depots, cleaning companies public building facades, electric starting self-propelled walking, self supporting legs, simple operation, large working area, and especially the ability to cross obstacles for high-altitude operations.
Safety operating procedures for aluminum alloy elevators.
Multi mast aluminum alloy lifting platform: the whole platform is refined by high-strength aluminum profiles. Due to the high strength of the profiles, the four mast structure is adopted, which has excellent stability, flexible operation, large load capacity, large platform area and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. Minimize the deflection of the lifting platform.
Bazhou.Attention must be paid to the rotating parts of the aluminum alloy elevator. When the engine is running. Hands and tools must be kept away from rotating fan belts and fans. During the test drive, it is necessary to be in a spacious area and ensure that the aluminum alloy elevator can safely stop and turn effectively.
It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time
Method: Check the length or diameter of the power supply lead. When the wire length is not more than 25 meters, the wire diameter should not be less than 1m ²; When the wire length is not greater than 50 meters, the wire diameter should not be less than 5m ². You can try fixing the plug directly to the socket without moving the cable.