Ascoy6061 aluminum barHow is the production status-World information network

bending deformation and torsion deformation are very easy to occur. Therefore, attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it, so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore, some other construction processes should be used, To solve some problems arising from the above production. For example, in the preliminary manufacturing of medical copper tubes for automobiles, the air conditioner copper tube materials can be selected according to the actual size required by the user, and then the air conditioner copper tubes for automobiles can be manufactured, followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching, and then stretching the pickled air conditioner copper tubes according to their size requirements. The warehouse shall not be mixed with acid Alkali, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, solar power generation support, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction, highway railings, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

Attention shall be paid to the purchase of red copper pipe in order to study the distribution law of pipeline crack stress field under internal pressure. The simulation ysis and experimental verification are carried out for pipes with cracks of different shapes, different directions different internal pressures and different sizes. The results show that the stress at the crack tip is much greater than that at the crack center. The crack shape has little effect on the stress. With the increase of the included angle between the crack direction and the pipe axis, the stress at the crack tip first increases and then decreases. With the increase of the pipe internal pressure, crack depth, and crack length, the stress at the crack tip increases linearly. Among them, the effect of crack length on the stress at the crack tip is smaller than that of internal pressure and crack depth. During the construction and operation of long-distance pipeline, due to the influence of pipe manufacturing defects welding defects, internal and external loads, stress concentration, corrosion defects and other factors, the pipeline will produce cracks and expand cracks, which is the most dangerous defect of long-distance pipeline and the main reason for pipeline failure. At present, pipeline cracks are mainly determined by internal testing and non-destructive testing after excavation. Among them, ultrasonic internal testing has a good identification rate for cracks with a length of more than 25 mm, a depth of more than 1 mm in the base metal or a depth of more than 2 mm in the weld; Magnetic flux leakage internal detection has a certain detection rate for cracks with opening more than 0.25mm, but it is difficult to identify and quantify. In NDT, magnetic particle, penetration, eddy current and radiographic methods have high detection and identification rate. The generation and propagation of cracks will cause local stress concentration in the pipeline, which is prone to brittle fracture, fatigue damage, corrosion damage and other failure phenomena, seriously affecting the service performance and reliability of long-distance pipeline. In this paper, the influence of crack shape, direction and size on the stress at the crack tip is yzed by studying the stress field distribution law of copper pipe cracks, forming, inspection and pipe expansion.

Ascoy. Finished products must be stored indoors. During storage, they should be protected from direct sunlight to the copper tubes. During the transfer, transportation and loading and unloading of copper tubes, rain should be avoided; In summer, the ambient temperature of copper pipe is high, and the speed of copper pipe surface is accelerated. When storing copper pipe, pay attention to the principle of first in first out to reduce no loss; The copper pipe loading process is better carried out indoors to avoid the copper pipe being exposed to the sun, so as to accelerate the speed of the outer wall of the copper pipe. After the loading is completed, at least two layers of canvas shall be used to tightly wrap the whole vehicle materials; After loading, if the truck can not depart in time, the truck shall be driven to the back of the sun to prevent the goods from being exposed to the sun for a long time to absorb heat.

Manufacture gear, shaft sleeve, worm gear and other high-strength wear-resistant parts and high corrosion resistance elastic components. Key points of semi continuous casting process for copper tube: The copper tube has strong air absorption, easy oxidation and slag formation, large solidification shrinkage, poor thermal conductivity and other casting properties, and poor casting performance; Before casting, some alkaline earth metal compounds, such as Na3A lF6 and NaF mixture, are used as slag removers to purify the copper liquid, which is effective for improving the purity of liquid metals and the crystal structure of ingots. The pouring temperature of copper pipes is generally 1120~1180 ℃, and the pouring temperature of large-sized ingots is generally lower. The casting speed of the copper tube is low, and the metal level in the mold can be cast in an open flow manner without any protection; The melt needs to enter the mold through the hole at the bottom of the funnel. The design of funnel aperture should meet two conditions at the same time: one is to ensure the flow matching the casting speed; Second, ensure that the liquid level in the funnel is always kept at a certain height, the joint coating must be carefully carried out to avoid concentrated shrinkage cavities in the ingot. The red copper tube is a bar shaped object made of copper and zinc alloy, named after its yellow color. Copper content is 56%~68% brass, and its melting point is 934967 degrees. Brass has good mechanical properties and wear resistance, and can be used to manufacture precision instruments, ship parts, gun casings, etc. Different zinc content also has different colors. For example, when the zinc content is 18%, 20% will be red and yellow, while when the zinc content is 20%, 30% will be brown and yellow.

.Four in one formula and process conditions Preparation of solution Take formula 1 as an example: mix the calculated amount of water for zinc oxide into a paste, slowly add it into the calculated amount of phosphoric acid under stirring until it is completely dissolved, then add zinc nitrate and tartaric acid, add sodium alkosulfonate and OP emulsion, and stir to make it completely dissolved. Then add chromium dihydrogen phosphate dissolved in dilute phosphoric acid, and add titanium sulfate. After all materials are added, dilute them to the total volume, stir them to make the solution even, cool them to room temperature, put a large amount of iron filings in the solution, and soak them for 2-3 days to make them contain enough ferrous ions. When the content of ferrous ion reaches above 7g/L, adjust the free acidity and total acidity of the solution to the specified value, and then the solution can be used at elevated temperature. When the ferrous ion reaches the above value, the phosphating speed is fast, the solution is stable, and the phosphating film is fine and dense. During operation, attention shall be paid to controlling the temperature. If the temperature is higher than 70 ℃, the degreasing technology of degreased copper pipe. How to make degreased copper pipe? The process flow of degreased copper tube? What are the characteristics of degreased copper tubes? Use of degreased copper tube? There are too many questions. Let's solve them at once. Everyone knows the copper tube. Nitrate reacts easily. The heater should be installed on the two walls of the tank, not on the bottom of the tank, to prevent local overheating. Stainless steel pipe or iron pipe should be used for heater, and lead pipe or copper pipe should not be used to avoid contamination of solution by impurities. What is degreased copper pipe? &The advantages of degreased copper pipe's comprehensive treatment of grease, rust removal, phosphating and passivation are described. This comprehensive treatment process can simplify the process, reduce the work area, save equipment costs, shorten working hours, improve labor productivity and reduce costs. This method can only be used in the occasions where the requirements for coating quality are not high.However, in actual production, due to the amount of oil contamination light and heavy rust, the consumption rate of each component in the solution is different, so attention should be paid to adjustment and control to maintain its due role. What is the degreasing copper tube? &I have roughly known the degreasing methods of degreasing copper tubes: solvent degreasing, alkali degreasing, ultrasonic degreasing high pressure hot water degreasing, electrolytic degreasing, etc. 1 Solvent degreasing: use degreasing solvent to dissolve the oil on the surface of red copper pipe collect it together into a container, volatilize, collect and reuse the volatile solvent, and separate the pollutants from the circulation system. This method was used in the early stage, which has problems such as low cleaning efficiency, difficult maintenance, and environmental pollution. In recent years, many kinds of surfactants have been developed.

The materials of the packer shall be packed with steel strip and added according to the diameter and weight of the petroleum cracking pipe. The degreased copper pipe from the pipe can be packed without a packer. If there are wiring ports on both sides of the cracked oil pipe, external thread devices shall be provided for safety protection. Brush the nozzle with clean oil or anti rust oil. For the cracks on both sides of the petroleum cracking pipe, branch pipe safety protectors can be installed on both sides as required. If the oil cracking pipe is installed in the container the container shall be lined with waterproof devices, such as woven cloth and straw mats. In order to better distribute the textile petroleum cracking tubes in the tank, the packer can weld the safety protection support frame inside the petroleum cracking tubes. Previous page: How to clean plastic coated copper tubes. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. When plastic coated copper pipe is cut, the wound is uneven and cracked. Then I will introduce how to solve these problems. For the disconnection part of plastic coated copper pipe, the position and direction shall be drawn with tape or other measuring tools and the disconnection line shall be marked in combination with the construction drawing and site conditions. When the petroleum cracking pipe is disconnected, please fix the equipment with square steel pipes such as vises, and cut it after fixing. In the area to be disconnected, use a towel or soft cloth to crack the oil stain or dirt on the surface of the pipe. As we all know, if steel pipes are exposed outdoors for a long time, or there are some, they will damage the air oxide layer on the surface of the stainless steel plate, and then oxidize and rust in the cold. Gas. Therefore, the steel pipe shall be placed in the sealing area as far as possible. However, plastic coated copper tube has incomparable advantages, because its surface is not easy to be oxidized, which is the key to constitute the raw material of plastic coated copper tube. The high-precision plastic coated copper pipe has an extremely thin, firm and smooth chromium rich air oxide film on its surface to prevent oxygen molecules from re penetrating and re oxidizing in the air, thus preventing rust. The description of the plastic coated copper pipe shows that the part with weak corrosion resistance of the transition film will produce pitting corrosion reaction due to the self-excited reaction, use tools such as clamps to fix the copper bar and then cut it, rather than fixing it by hand, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place, and then processed again after cooling, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, the global mining industry will rise again, and the W-shaped trend will fully emerge. In the second half of the year, there were signs of stabilizing and rebounding. In terms of the macro factors affecting the bulk commodities, the factors affecting the European market of tinned copper bars have gradually weakened, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, and the possibility of a crisis in the next period of time is also reduced. In recent years, the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, and the market price has rebounded to around 7600 dollars per ton. Driven by this products including aluminum, zinc and other products have also rebounded. Only nickel, a basic metal product, professional t2 copper tube manufacturers will adopt an integrated molding process to improve the yield and reduce production costs while packaging products with superior performance. As long as the above t2 copper tube quality identification method is used, it is basically guaranteed to purchase t2 copper tubes with reliable quality. If long-term and large-scale procurement is required, it is recommended to go to the manufacturer for field inspection to determine the basic performance and quality of t2 copper tubes before large-scale mold procurement. The position of grid accessories plays a very important role in the whole construction process. The products with high cost performance and good performance certainly have a great assistance effect for the implementation of the project. In addition, it is also beneficial to the application of the middle and later stage of the forming project. There are high regulations for the performance of the grid. How about the corrosion resistance of the grid accessories? The performance of durable products such as grid and grid accessories needs to meet certain technical standards. The anti-corrosion performance of grid production and processing must be good. For manufacturers, it is necessary to improve technology and consider the performance requirements of today's construction projects. In fact, the anti-corrosion performance of accessories is not very good. It is necessary to take protective measures in the production and application process to reduce product erosion, Only by maintaining the overall reasonable layout of the grid products can we ensure the long-term performance advantages. Many technologies are required in the whole process of production and manufacturing of space truss accessories. The production and manufacturing staff should ensure the performance advantages when carrying out production and manufacturing of products. The production and processing of space truss should improve its corrosion resistance, compression resistance and strength to ensure that qualified products are produced by the original factory.

Water with low PH value causes corrosion.

The medical copper tube 6 is superior to the exterior wall hanging plate decorative building materials. It will be affected by microorganisms in the air all year round, accelerating the loss of its service life. 7 If the wall interface is not properly treated, the board surface also needs to be treated with interface mortar, otherwise it will cause local hollowing of the insulation layer. How to protect the medical copper tube during installation? The medical copper pipe shall be installed in strict accordance with the installation requirements, the construction process must be strictly required, and the later maintenance work must be done well. 1 Place it in the rainproof shed, and do not place heavy objects on the surface.

Safety production.The demand for t2 copper tubes is increasing. At the same time, in the market, the quality identification method of t2 copper tube for grid fittings is currently accompanied by rapid economic development. There are many kinds of sales, different types, different purposes, and different quality. Therefore, you should be clear and have certain selection skills. Here we introduce the quality identification method of t2 copper tube. The color of t2 copper tube depends on the color of t2 copper tube. Although the external color is a visible factor, the color of the product is closely related to its production process and quality control. If the product is bright in color and high in glossiness, it is generally superior to the product with poor color. The t2 copper tube with uniform thickness should be selected. Because some small manufacturers are limited in technology and process, it is difficult to ensure that the product thickness is uniform and neat. Therefore, the thickness is also an important factor to test the quality of the pattern plate. Later, the casting process of t2 copper tube.

In addition, brass has a unique sound, so the gongs, cymbals, bells, as well as the western brass instruments, are all made of brass, which is a kind of non-ferrous metal processing bar, with good processing performance and high conductivity. It is mainly divided into copper tube (copper zinc alloy, cheaper). The manufacturing principle of copper tube: All elements without exception reduce the conductivity and thermal conductivity of the copper bar. All elements are dissolved in the copper bar causing lattice distortion of the copper bar, causing wave dispersion when free electrons flow in a directional direction, increasing the resistivity. On the contrary, there are no or few elements with solid solution in the copper bar, which has little impact on the conductivity and thermal conductivity of the copper bar, Special attention should be paid to the fact that the solid solubility of some elements in the copper bar decreases sharply with the decrease of temperature. The precipitation of simple substances and metal compounds can not only strengthen the copper bar alloy by solid solution and dispersion, but also reduce the conductivity slightly. This is an important alloying principle for the study of high-strength and high conductivity alloys. Here, it should be pointed out that the alloy composed of iron, silicon,Ascoy2205 stainless steel plate, chromium and copper bar is a very important high-strength and high conductivity alloy; As the influence of alloy elements on the properties of copper bars is superposition, CoCrZr series alloys are * high-strength and high conductivity alloys; It is not easy to heat. Semi continuous casting copper tube has excellent conductivity. Copper tube has excellent conductivity. Alloy copper to ensure safety and fatigue resistance. Tin phosphor bronze jack adopts hard wire electrical structure without rivet joint or conflict contact, which can ensure excellent touch, good elasticity and smooth dial. Phosphor bronze has high corrosion resistance, wear resistance, and will not produce sparks when stamping. It is used for medium speed and heavy load bearings. The working temperature is up to 250 ° C, and the active centering is insensitive to deflection. The bearing force is uniform, and the bearing capacity is high. It can withstand radial load and self lubrication without protection. The company is a manufacturer specializing in the production of various bronze tubes bronze rods, bronze plates and profiled bronze profiles. Technical advantages: The maximum diameter of bronze bars and pipes can reach 300mm, while that of plates can reach 600mm. The wall thickness of bronze tube can be as small as 4mm. The copper tube is a common bronze material. The aluminum content of copper tube generally does not exceed 5%. Sometimes, an appropriate amount of iron, manganese and other elements are added to further improve the performance. It has high strength and good wear resistance. It is used for copper sleeves and wear resistant parts with high strength. The outstanding feature of t2 copper tube is its good wear resistance. The difference between copper tube and copper tube The copper tube is a copper based alloy with aluminum as the main alloy element. The copper tube is a copper based alloy with tin as the main alloy element. The mechanical properties of copper tube are higher than that of copper tube. The aluminum content of the copper tube in practical application is between 5% and 12%, the aluminum content is 5%, and the 7% copper tube has good plasticity and is suitable for cold working.

Ascoy6061 aluminum barHow is the production status

Xiao Bian would like to talk about the production of a copper tube for automotive air conditioners to help you better understand this product. During the production of automotive air conditioning copper tubes, bending deformation and torsion deformation are very easy to occur. Therefore, attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it, so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore some other construction processes should be used, To solve some problems arising from the above production. For example, in the preliminary manufacturing of medical copper tubes for automobiles, the air conditioner copper tube materials can be selected according to the actual size required by the user, and then the air conditioner copper tubes for automobiles can be manufactured, followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching, and then stretching the pickled air conditioner copper tubes according to their size requirements. The warehouse shall not be mixed with acid Alkali, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, power plants, agricultural and chemical machinery, glass curtain walls, highway railings, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

resources.What problems should we pay attention to in each production. It is a key process to weld copper pipe with correct process. Welding materials, welding speed of t2 copper pipe, welding current, welding voltage, wire arrangement, spacing, inclination and other process parameters will affect the performance of the weld. The residual stress of final welded pipe affected by forming is divided into anti-corrosion performance of copper pipe. Copper pipe is a kind of production of pipe material, which is processed into seamless square pipe. The physical properties of copper tubes are slightly weaker than those of hot-rolled steel tubes. The copper tube adopts a two-step push tube expanding machine which integrates cone die tube expansion, data medium frequency induction heating and hydraulic press. With effective processing technology, low energy consumption, less infrastructure construction, good products, wide application fields of raw materials and products, and what are the production batches suitable for copper tube testing. When purchasing copper tubes, we pay more attention to their general possibilities and observations, but this is effective for a few customers, but it is time-consuming and labor-intensive for many customers, and then the following is how to conduct inspections. The dimension tolerance of the cleanliness and wall thickness of the inner cavity of the copper tube is strict. However, in the whole process of electric welding due to the role of the molten metal material of the air conditioning copper pipe, the thickness of the pipe at the welding point will be uneven, and the inside and outside of the welding will be uneven. This will cause energy consumption of the conveyor. At this time, the internal welding ground must be used for leveling. Next, we will take you to the production process of copper pipe - internal welding and calibration. At present, many materials are also used in the life of red copper pipes. Be as judgmental as possible when buying. In fact, there are many things to pay attention to when purchasing copper tubes. Want to keep high when buying. What should we pay attention to when buying copper tubes next. The daily use and market are calculated according to the weight, so you should decide how much to use before buying.

How to preserve the copper tube? In order to protect the excellent performance of copper pipes from the impact of the environment, we need to do the following: First, select appropriate sites and warehouses, and keep the surrounding environment dry and ventilated. Do not stack together with acid, alkali, salt, cement, etc.

The surface coating of medical copper tube is very important. Observe its thickness, how to prevent the aging of medical copper tube? How to select the foam density of medical copper tube Good medical copper tube and foam density are very high and hard. Check the quality of aluminum zinc coated color steel plate on the surface. As exterior wall thermal insulation decorative plate. Then use your hand to break it up and down to see if it is easy to deform. If you break it with force, it will deform, which is not good. 3 See the price.

Ascoy.Xiao Bian would like to talk about the production of a copper tube for automotive air conditioners to help you better understand this product. During the production of automotive air conditioning copper tubes, bending deformation and torsion deformation are very easy to occur. Therefore attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it, so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore, some other construction processes should be used, To solve some problems arising from the above production. For example, in the preliminary manufacturing of medical copper tubes for automobiles, the air conditioner copper tube materials can be selected according to the actual size required by the user, and then the air conditioner copper tubes for automobiles can be manufactured, followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching and then stretching the pickled air conditioner copper tubes according to their size requirements. The warehouse shall not be mixed with acid Alkali, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction highway railings, housing construction, pressure vessels, oil tanks, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

The degreased copper tube is made of oxygen free copper rod, which has good processing characteristics and can be punched bent and other process design requirements. The surface can be subject to anti-corrosion treatment, such as nickel plating, tin plating, zinc plating, etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, charging pile, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe, so as long as it is used correctly, few people ask about the water supply pipe of the house. In fact, the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and more than 99% of the water will disappear after entering the degreased copper tube for 5 hours. This biological characteristic is that there is a small amount of copper ions dissolved in water in the degreased copper tube, and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer which can resist extreme weather and is suitable for the long-term surface of metal materials. The actual effect of salt and water corrosion resistance is good. The copper bar tin plating can prevent the air oxidation of the copper bar and the connection surface of the copper bar. In addition, the melting of metal tin and copper will produce aluminum alloy, the conductivity of metal tin is good. The purpose of copper and tin plating: effectively prevent copper from becoming verdant due to moisture, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times, which greatly increases the service life of the copper and plays a considerable role in protecting the copper. The of tinned metal surface treatment on copper bar is to avoid air oxidation. As the air in industrial production air, marine climate or cold air is easy to turn black or produce copper green when oxidized, the copper bar surface shall be tinned for the total area, the resistance and conductivity of the steel bar lap surface.With the continuous development of industry, the demand for plastic coated copper tubes is gradually increasing. Then how to apply wood grain paint on alloy pipes. Wood like paint is a kind of wood like paint. It is used for spraying plastic coated copper pipe and its process flow. Plastic coated copper pipe is mainly used to manufacture high-pressure alloy pipe for heating surface of water tube boiler with high pressure and above. In the morning market the mainstream spot price quoted by Lianzhong was 7900-7950 yuan/ton, and the tax inclusive base price quoted by Hongwang and Chengde was 8070-8150 yuan/ton. On a month on month basis, part of the producing areas recalled 50 yuan,AscoyCopper aluminum composite row, and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP, UHP and subcritical power plant boilers. Third, large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

What problems should we pay attention to in each production. It is a key process to weld copper pipe with correct process. Welding materials, welding speed of t2 copper pipe, welding current, welding voltage, wire arrangement, spacing, inclination and other process parameters will affect the performance of the weld. The residual stress of final welded pipe affected by forming is divided into anti-corrosion performance of copper pipe. Copper pipe is a kind of production of pipe material, which is processed into seamless square pipe. The physical properties of copper tubes are slightly weaker than those of hot-rolled steel tubes. The copper tube adopts a two-step push tube expanding machine which integrates cone die tube expansion, data medium frequency induction heating and hydraulic press. With effective processing technology, less infrastructure construction, good products, wide application fields of raw materials and products, and what are the production batches suitable for copper tube testing. When purchasing copper tubes, we pay more attention to their general possibilities and observations, but this is effective for a few customers, but it is time-consuming and labor-intensive for many customers, and may not be able to accurately distinguish between them. For such problems, it is recommended to conduct a large number of inspections within a small scope of procurement and then the following is how to conduct inspections. The dimension tolerance of the cleanliness and wall thickness of the inner cavity of the copper tube is strict. However, in the whole process of electric welding, due to the role of the molten metal material of the air conditioning copper pipe, the thickness of the pipe at the welding point will be uneven, and the inside and outside of the welding will be uneven. This will cause energy consumption of the conveyor. At this time, the internal welding ground must be used for leveling. Next, we will take you to the production process of copper pipe - internal welding and calibration. At present, many materials are also used in the life of red copper pipes. Be as judgmental as possible when buying. In fact, so you should decide how much to use before buying.