Singapore5052 aluminum barAutomatic sealing performance characteristics

Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, the chromium content on the metal surface will, and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, causing corrosion of stainless steel. Therefore, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand, glass beads or other abrasives previously used on ordinary carbon steel, low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, the wire ropes, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, the air conditioning copper pipes need to be taken out and put into hot water for heating, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less the internal surface layer of the copper tube is larger, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, and its market potential is huge. Problems such as incomplete penetration, deformation cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, the structure and properties of the base metal are almost unchanged, so that the original service properties of the base metal can be maintained.

The plastic coated copper pipe is pollution-free, so the GRP sand pipe can be used to transport domestic water, and it is not easy to have the odor generated by the pipe itself.As we all know, the pipeline leakage problem is a problem that I can not always ignore. The area where GRP sand pipe is very easy to leak is leakproofness. The pH value of slurry in the desulfurization tower must be controlled within the range. If it is too low, the slurry will lose its absorption; On the other hand, if it is too high, the system software will cause relatively serious adverse effects of scale blocking, and the PH value will be adjusted according to the dynamic characteristics of dolomite feeding line. Relative density of desulfurization tower slurry. The thickness of plastic coated copper pipe is mainly determined by the four difficult problems: the number of layers of cloth, resin, cloth quality, and the thickness of glass fiber filament winding. The production and manufacturing of plastic coated copper pipe in China has a fast development trend, the total number is gradually rising, and the application scope and units are also increasingly wide. Plastic coated copper pipe is a kind of non-metallic material pipeline with light weight, high strength and corrosion resistance. The glass fiber with resin based weight relief shall be wound on the rotating hollow floor step by step according to the processing technology regulations, and the stone sand shall be used as the intermediate weathering layer on the long distance uniform pavement in the middle of the chemical fiber.

Singapore.In the first ten days of May, the overall order receiving quantity of Tianjin Hebei Henan Plate Plant was not ideal. According to the monitoring data, the overall order intake of medium and heavy plate mills in Tianjin Hebei Henan region in the first ten days of May remained stable and weak. Due to the weak market shock, the overall order intake of the spot steel market was relatively weak. The total quantity of orders received in the first ten days of May is only about 300000 tons, the total quantity of post settlement agreements of main steel plants can exceed 300000 tons.

In addition, the stress corrosion cracking inside the stainless steel plate will cause the transition film on the surface of the stainless steel plate. Therefore, and the fracture line shall be inclined to the pivot of the plastic coated copper pipe. Too large is the reason for cutting plastic coated copper pipe into flat or oval shape, so moderate energy shall be used when cutting square steel pipe. What matters should be paid attention to when purchasing plastic coated copper tubes.

.No heating and plating bath is required. The process is simple and easy to operate. The cold drawn degreased copper tube bright tin plating is one of the anti discoloration mirror bright brush tin plating and degreased copper tube tin plating mean copper bar partial or overall tin plating.

The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls,SingaporeTinned copper bar, boiler construction highway railings, housing construction, pressure vessels, oil tanks bridges, power station equipment, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

One of the classification of copper tubes. The common wave shape is a single copper tube. Hyperbolic means that two different arcs overlap on the same surface, that is, starting from different circle centers, draw arcs in two radii. The red copper tube is a module made of double curves designed according to the drawings. The red copper tube is light in weight good in rigidity and high in strength. The shapes of the red copper tubes processed are different and can be processed into various geometric shapes such as arcs and spheres. It is beautiful, elegant and colorful. Let's talk about the two main methods of processing and forming the copper tube: The hot processing and forming method is to roll the copper tube to a roughly hyperbolic shape, then heat it, then place it on the mold prepared in advance, then slowly beat it with a hammer, finally cut, weld, fold, polish and polish it. The whole process needs to be very careful to ensure the surface quality of the copper tube. This forming method is very suitable for parts with small model and large arc change. When the model size is relatively large and complex, it can be considered to break it into small pieces for forming, and then splice it into large pieces. For such copper pipes, the cost is high and the production period is long. 2 Forming method of roll bending This method is to make some modifications on the roll bending machine, and change one of the shafts into a concave type and the other into a convex type. This method can form a regular copper tube like a sphere, with a small processing range, but it has great advantages for copper tubes with small radians. What problems should be paid attention to when designing the hyperboloid copper tube? Everyone knows that the design of the air conditioning copper tube is very important. To achieve the beautiful shape, exquisite workmanship and fashionable personality of the hyperboloid copper tube, first of all, the design is very critical. Some small copper tube companies are not mature enough in design and have not enough design experience, so they often have problems in design, Hyperbolic copper tube is very famous for preparing some details that we should pay attention to in the design. The sculpted copper tube is highly decorative, and the production and processing technology of hyperbolic shaped copper tube is relatively complex. Copper tube products with strong aesthetics. According to the design requirements, different shapes need to be molded for the sculpted copper tube, so the production process of sculpted aluminum veneer is relatively complex.

Use the medical copper tube table to eat. Because of the unique of the medical copper tube, when the oil drops on the table, but not penetrate the table. Only with a slight wipe of the rag, the oil stains will be easily disappeared. In this case, when cleaning large canteens, the liquidators do not need to spend much effort but are relaxed. They just need to prepare a rag and a basin of clean water, and then carefully scrub it. t2 Medical Copper Tube Company thinks that the medical copper tube table is only made of the surface of the medical copper tube, and its exterior is not made of the medical copper tube. The price is cheaper than the wooden table, which is extremely suitable for a small amount of purchase. The medical copper tube has a natural bright and beautiful feeling. The color is extremely blended, and can stop the very good embellishment and reaction with the color in the surrounding situations. Now, let's understand some STEPs of the appearance processing of medical copper tubes. There are about five different methods for the appearance processing of medical copper tubes. Connect to t2 Medical Copper Tube Company and introduce them to the master. In addition, these methods can also stop the combined processing and create more medical copper tubes with different appearances. No matter which method is used, the following STEPs should be followed. First, before processing, the agreement should be stopped with the manufacturer, and then a sample should be selected as the standard for future consumption. The second part, when using it, we should guarantee that the coils of the base we choose to use and the coils that are not yet used are the third of the same model and batch. If they are used in some construction, such as elevators, we should pay attention to the unexpected selection of materials. In some places with extraordinary contrast, it is not appropriate to use the mirror t2 medical copper tubes. When processing, it is necessary to select the appropriate manufacturing process, such as weld grinding, pay attention to the bias, which is also called unidirectionality. For example, if the lines used are vertical rather than horizontal, STEP of the process used should be added, so the cost also needs to be added. Therefore, when selecting the appearance of the processing, t2 Medical Copper Tube Company revealed that Panbo consumers should carefully select according to the situation, and when selecting the planning and design staff, they should have a full understanding of the appearance of t2 Medical Copper Tube. Since the birth of medical copper tube, it has been widely used in food, chemical industry, crude oil machine manufacturing and other industries for its superior . It is precisely because of this kind of universal needs that people are increasingly demanding for medical copper tubes. Although this kind of situation is basically conducive to the development of the medical copper tube industry. Having said so much, the editor of this website will introduce the most popular technology in the medical copper tube industry -- the medical copper tube appearance fingerprint free disposal punishment technology. Mentioned here, I believe that many enemies have learned the greatest advantages of this kind of technology from the name. However, do you know that this is nothing more than a contrast of significant and abstract advantages. The most one-sided introduction is also my face. The medical copper tube after adopting this kind of technical treatment has a smooth appearance and soft hand feeling, and ordinary dust and impurities are not easy to adhere. Therefore, it is also extremely easy to clean. If the ordinary dust is probably dirt, just wipe it with a wet rag and you will lose the clean and smooth appearance. Because the implementation of this kind of craft is to use electroplating oil to shine the film on the red interior line, a superior appearance can always leave the best impression. Therefore, compared with the medical copper tube after the punishment and the medical copper tube without the punishment, it can often be welcomed by customers and enemies.Hot rolling and hot expansion. The main processing procedures include the blank sawing process, and the production process of the air conditioning copper pipe in the tower mainly includes cold drawing. Ring furnace heating process, piercing process, pipe rolling process, sizing process, cooling bed process, straightening process, pipe cutting soot blowing process, magnetic flux leakage detection process, length measurement and weighing to packaging and warehousing. Key points: yield strength limit: when the external force borne by the air conditioning copper tube sample exceeds the elastic limit of the material, although the stress no longer increases, the sample still has obvious plastic deformation. This phenomenon is called yield, that is, when the material bears an external force to a certain extent, its deformation is no longer in direct proportion to the external force, resulting in obvious plastic deformation. The stress when the air conditioning copper pipe yields is called the yield strength limit, and the corresponding S point in the tensile test curve is called the yield point. For air conditioning copper pipes with high plasticity, there will be an obvious yield point on the tensile curve, while for materials with low plasticity, there will be no obvious yield point, so it is difficult to calculate the yield limit according to the external force at the yield point. Therefore in the tensile test method, it is usually specified that the stress when the gauge length on the specimen produces 0.2% plastic deformation is taken as the conditional yield limit expressed as 0. The yield limit index can be used as the design basis for requiring that the parts do not produce obvious plastic deformation during operation.

However, it is difficult to change this situation too much in the short term. It is expected that the domestic strip steel price will mainly rise in the short term. It is reported that in order to pursue profits, Tangshan Iron and Steel Group Co., Ltd. is currently increasing the supply of hot coils. It does not rule out that more steel mills in the future are inclined to one end of the plate in pursuit of profits, or to lay hidden dangers for the decline. As far as tomorrow is concerned, the price may still maintain a narrow range of shock operation pattern.

One of the classification of copper tubes. The common wave shape is a single copper tube. Hyperbolic means that two different arcs overlap on the same surface, that is, starting from different circle centers draw arcs in two radii. The red copper tube is a module made of double curves designed according to the drawings. The red copper tube is light in weight, good in rigidity and high in strength. The shapes of the red copper tubes processed are different and can be processed into various geometric shapes such as arcs and spheres. It is beautiful, elegant and colorful. Let's talk about the two main methods of processing and forming the copper tube: The hot processing and forming method is to roll the copper tube to a roughly hyperbolic shape, then heat it, then place it on the mold prepared in advance then slowly beat it with a hammer, finally cut, weld, fold, it can be considered to break it into small pieces for forming, and then splice it into large pieces. For such copper pipes, the cost is high and the production period is long. 2 Forming method of roll bending This method is to make some modifications on the roll bending machine, and change one of the shafts into a concave type and the other into a convex type. This method can form a regular copper tube like a sphere, with a small processing range, but it has great advantages for copper tubes with small radians. What problems should be paid attention to when designing the hyperboloid copper tube? Everyone knows that the design of the air conditioning copper tube is very important. To achieve the beautiful shape, exquisite workmanship and fashionable personality of the hyperboloid copper tube, first of all, the design is very critical. Some small copper tube companies are not mature enough in design and have not enough design experience, so they often have problems in design, Hyperbolic copper tube is very famous for preparing some details that we should pay attention to in the design. The sculpted copper tube is highly decorative, and the production and processing technology of hyperbolic shaped copper tube is relatively complex. Copper tube products with strong aesthetics. According to the design requirements, different shapes need to be molded for the sculpted copper tube, so the production process of sculpted aluminum veneer is relatively complex.

Quality management.The plastic coated copper pipe is pollution-free, and it is not easy to have the odor generated by the pipe itself.As we all know, the pipeline leakage problem is a problem that I can not always ignore. The area where GRP sand pipe is very easy to leak is leakproofness. The pH value of slurry in the desulfurization tower must be controlled within the range. If it is too low, the slurry will lose its absorption; On the other hand, if it is too high, the system software will cause relatively serious adverse effects of scale blocking, and the PH value will be adjusted according to the dynamic characteristics of dolomite feeding line. Relative density of desulfurization tower slurry. The thickness of plastic coated copper pipe is mainly determined by the four difficult problems: the number of layers of cloth, resin, and the thickness of glass fiber filament winding. The production and manufacturing of plastic coated copper pipe in China has a fast development trend, the total number is gradually rising, and the application scope and units are also increasingly wide. Plastic coated copper pipe is a kind of non-metallic material pipeline with light weight, high strength and corrosion resistance. The glass fiber with resin based weight relief shall be wound on the rotating hollow floor step by step according to the processing technology regulations, and the stone sand shall be used as the intermediate weathering layer on the long distance uniform pavement in the middle of the chemical fiber.

It is applicable to the removal of thin liquid oil stain and light rust and the generation of phosphating film with certain corrosion resistance. See Table 3 for example of formula and operating conditions. Table 3 Degreasing, rust removal, phosphating and passivation

The editor of this website of t2 Medical Copper Tube Company said that if there is no table, they can only stand to eat and probably enjoy food in other places. In the catering industry, there are various kinds of tables, and all kinds of tables are available. There are wooden tables and medical copper controlled tables. This table controlled by red copper in Chinese medicine is most common in large canteens such as schools, while wooden tables can often be found in small restaurants as one of the steel products of medical copper tubes. As his name is common, medical copper tubes have the ability to prevent rust. In the catering industry, tables made of medical copper tubes have many advantages. Next, the teacher of Medical Copper Tube Consumption Co., Ltd. will introduce you to the master. The medical copper tube table is easy to see in the large canteen. This kind of canteen is extremely large, and the number of tables is amazing, so it is extremely difficult to settle accounts. If a wooden table is used, it will cost a lot of money, and it will also take a lot of work to settle after eating.

Plastic coated copper pipe is a kind of non-metallic material pipe with light weight, high strength and corrosion resistance. The plastic coated copper pipe is made of glass fiber with resin base weight, which is wound on the rotating hollow floor step by step according to the processing technology regulations, and the stone sand is laid on the ground evenly for a long distance in the middle of the chemical fiber as the intermediate weathering layer. The price quotations of plastic coated copper pipes with different thicknesses are also different. Here, we will explain the factors that determine the thickness of the plastic coated copper pipe design scheme. Appearance and specification of mpp cable duct 1 Color: generally orange red, other colors can be implemented according to the contract of both parties. 2 Appearance quality: The inner and outer walls of the pipe fittings shall be smooth, clean and even, and shall be free of steam bubbles, cracks, cracks, and obvious marks, dents, residues, dissolved discoloration lines and uneven colors. The inner holes of the pipe shall be laser cut and leveled and vertical to the pipe centerline. The inner holes shall be smooth and free of burrs. Specification: The length of pipe fittings is generally 6000 or 9000mm, which can also be negotiated by both parties. The specification error shall conform to dl/t801; The bending degree of the hose shall not exceed 1% of the nominal pressure. Some key points in the process of embedding plastic coated copper pipe: the embedding process of plastic coated copper pipe is very worthy of great attention. Although the actual operation in the process of embedding is relatively simple, there may be many key points. Pay special attention to the leveling and straightness of the road surface when threading, if the road surface is seriously uneven, it is seriously affected by external forces. Relevant countermeasures must be taken, and fine sand and dirt should also be prohibited from seeping into the pipe during the burial process, so as to diligently maintain its compliance with the regulations during the burial process. The process of embedding the plastic coated copper pipe involves the problem of marking. In fact, the marking that can be carried out according to this marking in the process of maintenance and repair is the key inspection index value of the commodity. If it is found that there is a problem with a certain section of cable, it is only necessary to find matching marks for immediate maintenance. Number of layers of cloth stacking: all layers are made strictly according to the design scheme, without additional construction, which increases the cost. 2 Resin: high temperature resistance, not easy to deform under stress. Plastic coated copper pipes are generally assembled from high-quality SMC water tank plates. Its characteristic is that it can select food grade stainless steel resin. Therefore, in view of the good water body,SingaporeT2 copper plate, the commodity development trend has certain characteristics such as high compressive strength, light weight, corrosion resistance, beautiful and generous appearance design scheme, long service life, and more convenient management methods in maintenance. Cloth quality: the specification of cloth surface is the same,Singapore6061 aluminum tube, pure platinum cloth is thick, and it is thick with blended cloth or pure old coarse cloth. The thickness of fiberglass filament winding: our products are high-tech support points of fiberglass anti-corrosion ring, which ensures the bearing pressure of the products. In addition, if you must select the thickened type, you can yze the vertical cross type difficult winding when winding the winding machine until the thickness and compressive strength of the thickened type are basically achieved.

Industry management.What problems should we pay attention to in each production. It is a key process to weld copper pipe with correct process. Welding materials, welding speed of t2 copper pipe, welding current, welding voltage, wire arrangement, spacing, inclination and other process parameters will affect the performance of the weld. The residual stress of final welded pipe affected by forming is divided into anti-corrosion performance of copper pipe. Copper pipe is a kind of production of pipe material, which is processed into seamless square pipe. The physical properties of copper tubes are slightly weaker than those of hot-rolled steel tubes. The copper tube adopts a two-step push tube expanding machine, which integrates cone die tube expansion, data medium frequency induction heating and hydraulic press. With effective processing technology, low energy consumption, less infrastructure construction, good products wide application fields of raw materials and products, and what are the production batches suitable for copper tube testing. When purchasing copper tubes, we pay more attention to their general possibilities and observations, but this is effective for a few customers, but it is time-consuming and labor-intensive for many customers, and may not be able to accurately distinguish between them. For such problems, it is recommended to conduct a large number of inspections within a small scope of procurement, and then the following is how to conduct inspections. The dimension tolerance of the cleanliness and wall thickness of the inner cavity of the copper tube is strict. However, in the whole process of electric welding, the thickness of the pipe at the welding point will be uneven, and the inside and outside of the welding will be uneven. This will cause energy consumption of the conveyor. At this time, the internal welding ground must be used for leveling. Next, we will take you to the production process of copper pipe - internal welding and calibration. At present, many materials are also used in the life of red copper pipes. Be as judgmental as possible when buying. In fact, there are many things to pay attention to when purchasing copper tubes. Want to keep high when buying. What should we pay attention to when buying copper tubes next. The daily use and market are calculated according to the weight, so you should decide how much to use before buying.

Three of the five major application fields of copper plate, copper bar and copper tube: copper is used to manufacture, and gun parts in the national defense industry. Every 3 million rounds of copper are produced, 13-14 tons of copper are needed.

The surface coating of medical copper tube is very important. Observe its thickness, how to prevent the aging of medical copper tube? How to select the foam density of medical copper tube Good medical copper tube and foam density are very high and hard. Check the quality of aluminum zinc coated color steel plate on the surface. As exterior wall thermal insulation decorative plate. Then use your hand to break it up and down to see if it is easy to deform. If you break it with force, it will deform, which is not good. 3 See the price.

Singapore.However, it may cause recoverable temporary damage to people who have been away from these radioactive sources for a long time. The DC brushless motor with small volume and large power is adopted, adhere to the wear form condition simulation criteria of the sample test select PVD chromium nitride ring and molybdenum spraying ring as the matching materials for the plastic coated copper pipe, use the self-developed opposed reciprocating wear tester, carry out the load level test, wear test lean oil test, and research the load. As for the corrugated process of the finished plastic coated copper pipe as claimed in claim 1, the radiation source for the engineering design of the integrated rigid flexible connection plastic coated copper pipe belongs to the low hazard source. Basically, it will not cause artificial damage. The basic principle of the foundation of the integral rigid flexible connection plastic coated copper pipe sluice discussed the influence of process parameters and heat treatment process on the microstructure, phase distribution and mechanical properties of the alloy, and obtained some important research results. The number of joints of steel pipes and plastic coated copper pipes on the same section shall not exceed 50% of the number of pipes. Before installation the pipe shed shall sweep and clean the hole with drill bit or high-pressure air, and the scum in the hole shall be removed, Ensure the aperture (The hole diameter shall not be less than 127cm, and the hole depth shall meet the requirements to prevent hole plugging. Most of the seamless steel pipes produced now are hot-rolled. Because of the high temperature, the deformation resistance is relatively small, and generally the steel plate is used for rolling. In this operation, the detailed thickness of the steel plate shall also be considered. If it is about the harmful elements with relatively low accuracy requirements, plastic coated copper pipes must be required. The pipe shed can be installed, extended section by section, and What does plastic coated copper pipe with a diameter of 1 reflect in life when the weld length is added to 30 for the joint steel pipe of the pipe extension joint? Plastic coated copper pipe can also produce welded pipes with different pipe diameters from billets of the same width. However, it can be compared with straight seam pipes of the same length. The rental production rate is low.

There are also some serious corrosivity, and some fine sand or vegetable oil coating will appear when the plastic coated copper tube packaging materials and packaging are stored according to special requirements. It can adhere to the surface layer and form excellent passivation effect on the surface layer of the plastic coated copper pipe. When cleaning, a cleaning plan is required. The plastic coated copper pipe must transport some raw oil in the industry. The plastic coated copper pipe has good air tightness to ensure no leakage of gasoline and diesel. It is a good transmission pipeline.

Pay attention to the following points when using flame heating brazing: the selection of welding materials The filler metal is wire or rod, with a diameter of about 35mm. The material is: the melting temperature of wire 221 is about 0905 ℃. Its chemical composition is FB10 The composition is 2331% H3BO3 and 6071% KBF The joint form of brazed copper pipe is mostly plug-in. Before cleaning the brazed copper pipe before welding, the edge of the pipe mouth must be corrected and deburred to ensure that the pipe mouth is free of cracks or other defects. And clean the surface of the inserted part. After the red copper pipe is assembled by tack welding, it shall be fixed by tack welding. The number, size and height of tack welds shall be symmetrically and evenly distributed along the circumference from top to bottom, left to right, and the tack welds shall be melted into the whole weld during brazing. When brazing the copper pipe, the flat angle position shall be used as far as possible to ensure continuous welding. Select the appropriate welding torch according to the size of the pipe joint. The flame of the former Han Dynasty should be neutral, because the oxidation flame has high oxygen content, which is easy to oxidize copper and cause cracks; The carbonization flame contains free hydrogen, which will cause pores. When heating pipes before welding, the flame shall be perpendicular to the heating surface, the pipe joints shall be heated evenly, and the base metal shall be heated as quickly as possible to avoid excessive temperature and heating time of the through pipe joints. During the brazing of degreased copper tube, the brazing seam and filler metal shall be under the protection of flame. In addition it shall be noted that the brazing seam shall be naturally cooled after welding, hot water or wet cloth shall be used to wipe the brazing seam and remove welding slag to improve corrosion resistance and reliability of post welding inspection.