MazetourHydraulic lifting platformThe technique of bending

the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it is necessary to exhaust the air in a timely manner.

Mazetour.In on-site hydraulic elevators, it is difficult to detect the rising position, middle position, impact noise, and oil film leakage of hydraulic cylinders. Field observations have shown that the excessive lifting speed of the hydraulic cylinder has led to an increase in failure rate, seriously affecting production efficiency. The unstable hydraulic lifting requires an analysis of the hydraulic oil flow rate. Hydraulic pressing oil has poor quality and contains a large amount of impurities, which can also prevent slow and unstable lifting. In addition, there are other reasons: lifting the composition of the hydraulic ring. Oil pump, safety valve directional valve, directional valve, one-way throttle valve (without throttling), and lifting cylinder.

When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking

.Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.

Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.

Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.

The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.

The hook or rope of the seat belt should be hung on a sturdy and sturdy component or a steel wire rope specifically designed for hanging the seat belt. Prohibit hanging on moving or unstable objects.

Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, stations, sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.

technical service.Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, stations, sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.

The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, with the advantages of higher lifting height, stable operation, and simple maintenance compared to the scissor fork type elevator.

Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.

Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.

Good reputation.When encountering signs of overheating in the electric motor, it is necessary to park the car in a timely manner, clean the problem,MazetourHydraulic lifting platform, and continue running. The motor bearings should be smooth and outstanding.

Oil pipe leaks oil. Poor sealing of oil pipes, resulting in a decrease in pressure and a natural descent of hydraulic cargo elevators. It is recommended to carefully check whether the oil pipes are intact and undamaged.

Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.

Mazetour.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.

To consider its capacity,MazetourHydraulic lifting platform fixed hydraulic, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.

Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap first remove the soil around the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning loosen the tank cap, open the tank cap.