ZamoshikHydraulic lifting platform truckWhat are the protection methods

I believe many people want to know about the maintenance issues of guide rail hydraulic lifting platforms, as it is related to their service life. During use, frequently check the connection of each part. If loose, the tightness of the connecting bolts of the body should be checked (the pressure state that can be used). All connecting shafts should have split pins and hydraulic cargo elevators should be fully opened.

Pre install equipment, maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, some require equipment such as forklifts for installation, it can prevent oil changes or blockage of system components. However full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.

Zamoshik.How to maintain the cleanliness of hydraulic elevators. If more high-quality hydraulic oil is added,ZamoshikMobile hydraulic lifting platform, these additives will lose their effectiveness after a period of time.

Lines of various safety equipment

.The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time,ZamoshikMobile elevator hydraulic lifting platform, it inevitably increases the distance of handling tools/vehicles in the workshop.

The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is easy for hydraulic cargo elevator manufacturers to cause this problem.

Hydraulic oil deteriorates or produces impurities. After long-term use of oil pressure, there may be impurities or deterioration in the oil. Sampling inspection should be carried out to see if there are solid particles, discoloration, and odor. If necessary, the oil should be changed. There may be blockage in the hydraulic pipeline of the hydraulic cargo elevator. The hydraulic pipeline is also a very important part, and it is necessary to check whether the hydraulic pipeline is smooth. Focus on checking whether each type of hydraulic valve includes one-way globe valve, electromagnetic directional valve, proportional control valve, overflow valve, etc. If there are problems, the hydraulic valve should be cleaned or replaced in a timely manner.

Separate: Loading and unloading on different platforms.

Welcome calls .The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.

Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

Lines of various safety equipment

Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.

Quality recommendation.Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.

Safety advantages: Hydraulic elevators are equipped with the safety devices of traditional traction elevators: overflow valve: it can prevent system pressure from being too high when going up; Emergency manual valve: In case of power failure, it can cause the car to emergency descend to the nearest floor position, causing the car to emergency descend to the nearest floor position, and causing the emergency in the car to descend to the nearest floor position; Pipeline rupture valve: When the hydraulic system's pipeline ruptures and the car stalls and descends, it can automatically cut off the oil circuit and stop descending; Oil temperature protection of oil tanks: When the oil temperature of the oil tank exceeds the standard setting value, the oil temperature protection device sends a signal to stop the use of the elevator and wait for the oil temperature to decrease before starting the elevator. Long term promotion of downgrading manufacturers, 20 year old brand, with price advantages and guaranteed quality!

Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, stations sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.

Zamoshik.The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time it inevitably increases the distance of handling tools/vehicles in the workshop.

Oil leakage from the oil cylinder: If it is a problem with the sealing ring,ZamoshikMobile hydraulic lifting table supply, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.

The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.