MingshanElevat
MingshanManufaAnd, it is convenient for our production and life.
When using, the weight should be evenly distributed, mainly in the center of the countertop. However, for special cases, partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load so this detail needs to be noted during use.
Mingshan.The correct operating method should be used, and during the design process, relevant debugging should be carried out. The key technical indicators should be able to meet the design requirements. When using the electrical system should also be connected to the power supply and meet the specified operating range and standards before operation can be carried out. At the same time, when conducting inspections, the systems of these platforms are also very important. They should be able to check for any leakage so that they can be used more smoothly in the later stage.
When a hydraulic lifting platform truck malfunctions,MingshanSmall lifting platform truck, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
.At the same time, the elevator can work efficiently during use, such as on a 50 meter or 10 meter high workbench. If traditional methods are used, this work will take a relatively long time. However, which can improve work efficiency and complete this work in a short time, It can be seen that elevators have many advantages during use.
The use of lifting platform vehicles must be operated by personnel designated by the department (registered by the Human Resources and Security Department) and strictly adhere to their work positions; Non designated personnel are not allowed to use it without authorization.
Before using the lifting platform vehicle, first check whether the doors of each floor are closed and whether the emergency stop switch is reset (the emergency stop switch is reset, rotate clockwise), and check the side of the emergency stop switch. After completion, the operation can be started.
After starting work every day, the elevator driver needs to carry out standardized operations. Of course, before carrying out the operation, the elevator needs to be inspected to ensure its safety before proceeding with the operation. The user unit needs to conduct a comprehensive inspection of the construction elevator every month and record the inspection results accordingly.
There are many options for platform selection, and whether it is color or style, these design situations are very important. When selecting aluminum alloy lifting platform vehicles, some key equipment information and specific parameters are crucial
According to the needs of different performance genres, using an orchestra pit lift can combine a framed stage with a large lip or even an extended stage. In an experimental theater, using a lift can make the theater have various forms such as an end stage, an extended stage, an island stage, an intermediate stage, a T-shaped stage, or a hall.
market.After starting work every day, the elevator driver needs to carry out standardized operations. Of course, before carrying out the operation, the elevator needs to be inspected to ensure its safety before proceeding with the operation. The user unit needs to conduct a comprehensive inspection of the construction elevator every month and record the inspection results accordingly.
When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to provide more than 6 months before proceeding, and it is also necessary to retest the construction elevators and test the acceptance results before proceeding. Therefore,MingshanRotating lifting platform truck, this point requires everyone's attention and understanding. When carrying out repairs or maintenance, it is necessary to follow the instructions of the construction elevator. The main purpose of repairing or maintaining the elevator is to ensure that each component can operate well. For factory elevators, rated load tests are required. Especially for elevators under construction, it is necessary to conduct a rated weight drop test every three months, cut off the power supply during maintenance, and set up eye-catching warning signs. Construction elevators with safety hazards are not allowed to be used.
If encountering or affecting the safety technical performance of construction elevators, it is necessary to provide more than 6 months before proceeding, and it is also necessary to retest the construction elevators and test the acceptance results before proceeding. Therefore, this point requires everyone's attention and understanding. When carrying out repairs or maintenance, it is necessary to follow the instructions of the construction elevator. The main purpose of repairing or maintaining the elevator is to ensure that each component can operate well. For factory elevators, rated load tests are required. Especially for elevators under construction, it is necessary to conduct a rated weight drop test every three months, cut off the power supply during maintenance, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, but also have certain energy-saving and environmental protection significance. Everyone knows that the country attaches great importance to this aspect now, so the requirements for many industries are also relatively high. If you are using this type of lifting equipment, you can rest assured about this aspect. Because it not only generates relatively low power consumption during actual use,MingshanTelescopic lifting platform vehicle, but also does not generate noise during operation.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
Mingshan.Elevator operators need to strictly comply with safety operating procedures during the operation process, in order to pay attention to relevant matters, especially before the operation, they need to focus on routine inspections or maintenance work. It is important to hold a special operation certificate before starting work.
When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations it can only briefly overload by 10%.