KoninPlatform 
KoninCylinder Safety protection components, in order to ensure safety production, guardrails, protective covers, platform stairs etc.
Safety protection components, in order to ensure safety production, it is essential to install a lifting platform for proper protection. The main protective accessories include safety belts, guardrails, protective covers, platform stairs, etc.
Konin.The electric lifting platform needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
Regularly check all wires and cables for damage, and promptly wrap and replace the damaged parts.
.Copyright © 2006-2022 Yan-wei.Net.All Rights Reserved.
Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple,KoninHeavy hydraulic lifting platform, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
Using Help | Updating Logs | Original Software | Daily Software
Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.
Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
Special manufacturing processes. Everyone knows that fixed loading and unloading platforms can have a good market performance, which is closely related to the advanced manufacturing technology of manufacturers. In fact, there are still many advanced processes that can be used nowadays. If used appropriately in daily production and manufacturing processes,KoninLarge hydraulic lifting platform, it can still improve the quality and production efficiency of manufacturers' products to a certain extent. As for this type of loading and unloading platform, which makes it highly stable in application.
index.High altitude work requires the use of tool bags, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.
Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged and after changing the hydraulic oil, maintain sufficient space, and ensure that the lifting platform can be lifted to the rated lifting height.
Pay attention to checking each part of the steel wire rope for broken wires and loose strands. If the tide passes through the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil, it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged, maintain sufficient space, and ensure that the lifting platform can be lifted to the rated lifting height.
Superior quality.Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
When using the elevator, we should listen for any abnormal noise. If there is any abnormal noise, we should immediately stop using it to avoid serious damage to the elevator.
Konin.Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Of course, when choosing a lift, it is also necessary to consider its production. If a manufacturer has a large production capacity, it indicates its strong strength especially the construction lift has relatively high requirements for production technology. Therefore, when making a purchase, it is important to consider the factory building and process of its production, all of which are very important.
The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform, or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, open platforms do not have doors. The electrical part is composed of power, safety, lighting and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts, which are composed of hydraulic pipe fittings,KoninHydraulic work platform, pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, door electromechanical interlocking, rupture valves, emergency switches, and electrical short circuit protection.