LimogesWher
KircheHydrauliThe product has a sturdy structure, a large load-bearing capacity, smooth lifting, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance, they must hang the elevator to prevent sudden lowering of the platform and causing casualties.
Small typesetting Copyright Shu ICP Bei No. 11019783-1
Limoges.When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
The drive motor can stop the movement of the rack on the pillar.
.The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, the lifting platform platform platform that carries the load needs to be balanced, and no deviation of one side is allowed. The lifting of goods does not allow people to stand on both sides of the platform, and the lifting of goods should try to maintain a stable and uniform speed.
Application and characteristics of stage elevators: Stage elevators, also known as lifting stages, are specifically installed on the stage and used for lifting and rotating the stage. They are called stage elevators. It has multiple functions such as lifting, rotating and tilting, and adopts protective measures such as self-locking, interlocking, travel switch, mechanical limit, hydraulic explosion-proof, etc.
Using Help | Updating Logs | Original Software | Daily Software
To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.
The current fixed hydraulic elevators are mainly enclosed or meshed lifting channels surrounded by buildings and light steel structures, and use hydraulic cylinders to lift the platform. Its main components are as follows: the lifting passage part: a closed or mesh frame surrounded by buildings or light steel structures, a fixed hydraulic lifting platform with steel guide rails installed on both sides of the internal driving part: it is equipped with hydraulic driving motors, oil pumps, safety valves, fixed hydraulic lifting platform speed control valves The small oil tank cylinder part of hydraulic components such as directional valves: composed of one or more cylinders of a lifting cylinder, a straight top platform or a lifting shear fork frame, forming a door system. The closed or mesh platform door or door system consists of a steel structure, with manual and automatic doors. Generally, open platforms do not have doors. The electrical part is composed of power, signal, safety, lighting, and other devices. The platform part is a steel structure platform that carries heavy objects, There are enclosed (i.e. cabin type) or open types, with guide rollers or guide shoes on both sides. The platform bottom can be connected to the lifting cylinder or lifting scissor type steel frame auxiliary parts,LimogesElectric three wheel hydraulic lifting platform, which are composed of hydraulic pipe fittings, pipelines, pressure gauges, and steel structure bases; Safety devices: safety valves, limit limits, rupture valves, emergency switches, and electrical short circuit protection.
Test results.Check the rollers intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.
agent.Maintenance time regulations for hydraulic elevators: After 1500 hours of daily maintenance of the elevator, repair the mechanical and electrical systems.
Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.
Limoges.Application and characteristics of stage elevators: Stage elevators, also known as lifting stages, are specifically installed on the stage and used for lifting and rotating the stage. They are called stage elevators. It has multiple functions such as lifting, rotating, and tilting, and adopts protective measures such as self-locking, interlocking, travel switch, mechanical limit, hydraulic explosion-proof,LimogesOutdoor hydraulic lifting platform, etc.
Because hydraulic elevators have the function of automatic and flexible lifting, they can provide protection for the safety of the campus and surrounding areas. Hydraulic elevators have many advantages, such as the ability to use hydraulic drive, it also has no blind spots and is sturdy and reliable during normal use. The important thing is that the possibility of compression and collision resistance is relatively small, so it is very convenient to use, and it is beautiful and durable. Among them, its guidance is relatively good,LimogesElectric hydraulic platform, with the characteristics of flexibility, reliability, and collision resistance.
Tail signature: