SivednikaPlatform hydraulic lifting platformAwareness of operating procedures management

Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil, it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged,SivednikaHeavy hydraulic lifting platform, and ensure that the lifting platform can be lifted to the rated lifting height.

The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!

Sivednika.The electric lifting platform needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.

Firstly, an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform adopts heavy-duty chain transmission, safety devices to prevent overloading, multiple limit switch protection, door and power outage protection, leakage protection, and multi-layer building interaction. Therefore, the safety factor of the guide rail hydraulic lifting platform is still very high, much higher than that of ordinary platforms.

.Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.

There are many types of materials that manufacturers can use in the manufacturing process of the same lifting equipment, but the lifting equipment manufactured from different materials will also be different. The material used by manufacturers in the manufacturing process of aluminum alloy elevators is aluminum alloy with very high strength. It should be noted that this type of material itself has many advantages, so the sales of the elevator equipment made in the market are also considerable. Of course, for many people the reason why they choose this type of lifting equipment is also closely related to its marketing highlights.

We

Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.

The characteristics of hydraulic lifting platforms are obvious, such as their relatively light overall weight and good maneuverability allowing even a single person to operate, making them relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, attention should also be paid to the structure of the hydraulic lifting platform to ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.

High stability of manufacturing materials. Usually, manufacturers can choose a variety of manufacturing materials when producing fixed loading and unloading platforms, and each material brings different effects when used. For many manufacturers, in order to improve the stability of loading and unloading platforms during use, they attach great importance to the selection of manufacturing materials. Generally, materials with high stability will be used as much as possible, as such materials can achieve better results in application.

Interpretation and observation.The reduction gearbox, gearbox, and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.

Website homepage

When using the elevator, we should listen for any abnormal noise. If there is any abnormal noise, we should immediately stop using it to avoid serious damage to the elevator.

If there are problems inside the elevator and electrical professionals are present, any components of the hydraulic system should be disassembled and repaired in a completely depressurized condition.

knowledge.Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors,SivednikaAutomatic hydraulic platform for lifting and lowering, and oil cylinder once a week to avoid dust and debris affecting normal operation.

For lifting platforms without manned protection, it is strictly prohibited to carry people during use. At the same time, attention should be paid during use to prevent damage to hands, feet, and clothing.

When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.

Sivednika.There are many options for highlight styling. In fact, although types of lifting equipment can also bring certain effects during use, their design is relatively limited. Basically,SivednikaHydraulic fixed lifting platform, the styles and shapes of lifting equipment in the market are similar. And aluminum alloy elevators are different because the plasticity of aluminum alloy materials is very strong. In the production process, it can also well meet some complex styling needs. The lifting equipment processed in this way will naturally have good sales in the market. After all, it has a wide range of styling options and can well meet the needs of different customers.

Hydraulic loading elevators must strictly carry out load-bearing operations in accordance with regulations. Otherwise it may harm people and objects!

Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.